Installation Guide

INSTALLATION INSTRUCTIONS
Item#P934-688-L (New. 02/29/2020)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
Fig. 3
MOUNTING
THE FIXTURE
(Fig. 1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the existing fixture and its mounting
hardware from the ceiling.
2. Carefully remove the new fixture from the carton and check
that all parts are included as shown in the illustration.
3. Thread the screws (E) into the pre-drilled holes of the circular
strap (A) spaced the same distance apart as the holes in the
canopy (C) of the fixture body.
4. Attach the circular strap (A) to the outlet box using the two
mounting screws (B) (size: #8-32N*L0.5”). The side of the
circular strap marked “GND” must face out.
5. Remove metal screw (I) from metal bushing (H). Determine
the desired hanging height by pushing or pulling the cord
through the center of metal bushing (H). Ensure the cord has
no less than 4’’ exposed.
6. Secure the cord by tightening metal screw (I) into the metal
bushing (H). Cut excess wire leaving about 5” of the cord for
the electrical connections.
7. Carefully cut and remove approximately 4” of the outer
sheathing from the cord and strip 1/2” of the wire ends bare to
expose the copper strands.
CONNECTING THE WIRES (Fig. 2)
8. Connect the electrical wires as shown in Fig. 2, making sure
that all wire connectors are secured. If your outlet has a
ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the circular strap (A) using the green screw
provided.
9. Tuck the wire connectors neatly into the ceiling junction box.
COMPLETING THE INSTALLATION (Fig. 1)
10. Raise the canopy (C) and slide screws (E) through canopy (C)
and secure with knurled knobs (D).
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified electrician
without cutting of wire and without damage to any
decorative element to which the fixture is attached. See
installation steps for more details (Fig 3.)
a. Shut off the power.
b. Remove the knurled knobs (D) and remove the wire
connectors and place fixture body on a clean flat surface.
c. Loosen screws (K) and remove fixture body (J).
d. Loosen the screws (O) and remove the lens (N).
e. Press the button of the printed “L” quick connector on LED
module (M) with screwdriver (not included) to disconnected
the black wire and then disconnect the white wire from the
printed “N” quick connector on LED module (M).
f. Loosen plastic screws (F) and remove the LED module (M).
g. Reverse steps b-f for installing the new LED module.
Your installation is now complete. Return
power to the
outlet box and test the fixture.
Note: The illustration in figure 1
on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
Dimmable with ELV and/or LED compatible wall dimmer
switches.
LA-3248E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper or
Green
(Ground)
HOUSE
WIRES
Green
(Ground)
Set
#
A
-
020
- Circular strap
- Ground screw
- Mounting screw*2
IMPORTANT: FIXTURE SHOULD BE INSTALLED
BY A QUALIFIED ELECTRICIAN TO ENSURE
PROPER WIRING AND INSTALLATION.
I
H
C
J
E
A
B
D
L
M
F
N
J
K
O
Screw d
river