SDS
5.3 Advice for firefighters
●
No action shall be taken involving any personal risk or without suitable training.
Move containers from fire area if you can do it without risk.
Structural firefighters' protective clothing will only provide limited protection.
Wear chemical protective clothing that is specifically recommended by the
manufacturer. It may provide little or no thermal protection.
Wear positive pressure self
-
contained breathing apparatus (SCBA).
Section 6
-
Accidental Release Measures
6.1 Personal precautions, protective equipment and emergency procedures
Personal Precautions
●
Ventilate enclosed areas. Wear appropriate protective clothing. Do not touch or walk
through spilled material.
Emergency Procedures
●
ELIMINATE all ignition sources (no smoking, flares, sparks or flames in immediate
area) As an immediate precautionary measure, isolate spill or leak area for at least 50
meters (150 feet) in all directions. If tank, rail car or tank truck is involved in a fire,
ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for
800 meters (1/2 mile) in all directions. LARGE SPILL: Consider initial downwind
evacuation for at least 300 meters (1000 feet) Keep out of low areas. Stay upwind.
Keep unauthorized personnel away. Ventilate closed spaces before entering.
6.2 Environmental precautions
●
Prevent entry into waterways, sewers, basements or confined areas.
6.3 Methods and material for containment and cleaning up
Containment/Clean
-
up
Measures
●
Stop leak if you can do it without risk.
A vapor suppressing foam may be used to reduce vapors.
Absorb with liquid
-
binding material (sand, diatomite, acid binders, universal binders,
sawdust).
Use clean non
-
sparking tools to collect absorbed material.
All equipment used when handling the product must be grounded.
6.4 Reference to other sections
●
Refer to Section 8
-
Exposure Controls/Personal Protection and Section 13
-
Disposal
Considerations.
Section 7
-
Handling and Storage
7.1 Precautions for safe handling
Handling
●
Keep away from fire.
Keep away from heat and sparks. Do not eat, drink or smoke
when using this product.
After handling wash hands thoroughly. Prevent formation of
aerosols. All equipment used when handling the product must be grounded. Bond and
ground all transfer containers and equipment. Take precautionary measures against
static charges. Containers, even those that have been emptied, can contain explosive
vapors. Do not cut, drill, grind, weld or perform similar operations near container.
7.2 Conditions for safe storage, including any incompatibilities
Storage
●
Keep containers properly sealed in a cool, dry, well
-
ventilated area between 65
-
85F
(18.3
-
29.4C). Do not store in open, unlabeled or mislabeled containers. Do not reuse
empty container without commercial cleaning or reconditioning.
7.3 Specific end use(s)
●
Refer to Section 1.2
-
Relevant identified uses.
Section 8
-
Exposure Controls/Personal Protection
8.1 Control parameters
All Purpose Bonding Adhesive LVOCAll Purpose Bonding Adhesive LVOCAll Purpose Bonding Adhesive LVOCAll Purpose Bonding Adhesive LVOC
Preparation Date: 03/February/2012Preparation Date: 03/February/2012Preparation Date: 03/February/2012Preparation Date: 03/February/2012
Revision Date: 29/August/2013Revision Date: 29/August/2013Revision Date: 29/August/2013Revision Date: 29/August/2013
Format: EU CLP/REACH Language: English (US)Format: EU CLP/REACH Language: English (US)Format: EU CLP/REACH Language: English (US)Format: EU CLP/REACH Language: English (US)
WHMIS, EU CLP, EU DSD/DPD, OSHA HCS 2012WHMIS, EU CLP, EU DSD/DPD, OSHA HCS 2012WHMIS, EU CLP, EU DSD/DPD, OSHA HCS 2012WHMIS, EU CLP, EU DSD/DPD, OSHA HCS 2012
Page 6 of 16Page 6 of 16Page 6 of 16Page 6 of 16