Operator's Manual

What do xed code dip switches look like and how do I convert them to button presses on my new universal remote?
If the opener has a group of 9 switches with 3 positions per switch (TRINARY):
• Switch in the UP position = Press button 1
• Switch in the MIDDLE position = Press button 2
• Switch in the DOWN position = Press button 4
In this example, the button presses would be:
If the opener has a group of 9-12 switches with 2 positions per switch (BINARY):
+
-
1 2 3 4 5 6 7 8 9 10 11 12
STEP 1: Each shaded box below represents a DIP switch position. In these boxes, write in the number 1, 2 or 4 as it corresponds to the
UP, MIDDLE or DOWN switch position you see on the remote, opener head or receiver.
Convert the 9 switch code:
In this example, the button presses would be:
• Switch in the UP position = Press button 1
• Switch in the DOWN position = Press button 4
4 1 1 1 1 1 1 14 4 4 4
+
0
-
1 2 3 4 5 6 7 8 9
4 41 1 1 1 1 22
1234504392, 11/2019
Universal Wireless Keypad
Instructions
It is recommended to complete programming before mounting keypad
Keypad
Up/DownKey
(enter)
ProgramKey
LED
LEDO
LEDOn
LEDFlashing
KeypadO
KeypadOn KeypadFlashing
Keypad LED’s
Successful Entries Failed Entries
SAVE THESE
INSTRUCTIONS
FOR FUTURE
USE
WARNING
!
MOVING DOOR CAN CAUSE SERIOUS
INJURY OR DEATH.
•DO NOT install transmitter (keypad) unless the door operator’s
safety device works as required by the door operator’s manual.
• Wall Console must be mounted in sight of door, at least 5 feet
above oor and clear of moving door parts.
•Keep people clear of opening while door is moving.
•DO NOT allow children to play with the transmitter or door
operator.
If safety reverse does not work properly:
•Close door then disconnect opener using the manual release
handle.
•DO NOT use transmitter or door operator.
• Refer to Door and Door Opener Owner’s Manuals before
attempting any repairs.
AVERTISSEMENT
!
DÉMÉNAGEMENT PORTE PEUT CAUSER DES
BLESSURES GRAVES OU LA MORT.
• NE PAS installer le transmetteur (clavier) à moins que le dispositif
de sécurité de l’opérateur de porte ne fonctionne comme l’exige le
manuel d’utilisation de la porte.
• Console murale doit être monté en vue de la porte d’au moins 5
pieds au-dessus-de-chaussée et claire des pièces mobiles de la
porte.
• Garder les personnes clair de l’ouverture lorsque la porte est en
mouvement.
• Ne pas laisser les enfants jouer le premier match à distance ou la
porte.
Si la sécurité inverse ne fonctionne pas correctement:
• Fermer la porte, puis débranchez moteur à l’aide de la poignée de
déverrouillage manuel.
• Ne pas utiliser d’ouverture à distance ou la porte.
• Reportez-vous à la porte et ouvre-porte de propriétaires manuels
avant de tenter toute réparation.
Keypad LED will ash and beep
each time a key is pressed and
entry is accepted.
Keypad LED and PROGRAM key
will ash slowly and number pad
back light will remain on for 15
seconds indicating a successful
program or valid PIN has been
entered.
Keypad LED, PROGRAM key and
number pad back light will ash
rapidly indicating a problem with
programming or an invalid PIN entry.
• Press the 7 & 9 keys together 3
times to start over.
Keypad Overview
Activate keypad by opening battery
compartment and pull protective
tab. Reinstall compartment door to
begin programming.
TAB
Scan this code with a QR code reader app on a smart
device to view a video of these instructions or visit
www.geniecompany.com
ID BRAND-TYPE FREQ-
MHz
TYPE INSTR
Group
DESCRIPTION
1 Genie Intellicode 1 315,390 Rolling 1 Genie Intellicode and OHD Mfg from 1995 to present
2 Chamberlain
(Purple)
315 Rolling 1 Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic, and Do
It GDO mfg from 2005 to present (purple button)
3 Chamberlain
(Orange/Red)
390 Rolling 1 Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic, and Do
It GDO mfg from 1997-2004 (orange/red button)
4 Chamberlain
(Yellow)
390 Rolling 1 Chamberlain, Sears Craftsman, and LiftMaster GDO mfg from 2011 to
present (yellow button)
5 Chamberlain
(Green)
390 Rolling 1 Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic, and Do
It GDO mfg from 1993-1996 (green button)
6 Genie Intellicode 2 315,390 Rolling 1 Genie Intellicode and OHD Mfg from 2011-2012 <what else?>
7 Sommer 310 Rolling 1 <need details>
8 Linear 318 Fixed-
Learn
1 Linear GDO mfg from 1997 to present
9 Wayne Dalton 372.5 Rolling 1 Wayne Dalton GDO mfg from 1999 to present
10 Ryobi 372.5 Rolling 1 Ryobi GOD mfg from 2016 to present <correct?>
11 Guardian 303 Fixed-
Learn
1 Guardian and Xtreme GDO mfg from 199x to present <dates? Want
others listed, like Boss, Decko, etc?>
12 Marantec 315 Fixed-
Learn
1 Marantec GDO mfg from 199x to present <dates?>
13 FAAC 433.92 Rolling 1
14 FUTURE reserve
15 FUTURE reserve 1
16 FUTURE reserve 1
17 FUTURE reserve 1
18 FUTURE reserve 1
19 FUTURE reserve 1
20 FUTURE reserve 1
21 Genie - 12 switch
binary
390 Fixed-Dip 2 12 DIP switch Genie GDO
22 Genie - 9 switch
binary
390 Fixed-Dip 2 9 DIP switch Genie GDO
23 Stanley - 10 switch
binary
310 Fixed-Dip 2 10 switch Stanley and Moore-O-Matic GDO
24 FUTURE reserve
25 FUTURE reserve
Find the model of the garage door opener(s) that this keypad will be operating from the chart below.
Mark down the pertinent information in the section below this chart.
BOX A:
Opener ID - DOOR #1: __________________
Opener ID - DOOR #2: __________________
Opener ID - DOOR #3: __________________
BOX B:
Fixed Code Switch ID - DOOR #1: __ - __ - __ - __
Fixed Code Switch ID - DOOR #2: __ - __ - __ - __
Fixed Code Switch ID - DOOR #3: __ - __ - __ - __
FCC Part 15.21 Statement:
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
Single Door Operation:
1. Ensure number pad back lighting is o.
2. Enter PIN.
3. Press the UP/DOWN key.
4. Opener will operate.
Multi-Door Operation:
1. Ensure number pad back lighting is o.
2. Enter PIN.
3. Press the UP/DOWN key.
4. Press number key corresponding with desired door (1, 2, or 3).
5. Desired opener will operate.
For questions, comments or troubleshooting, contact The Genie Company at:
1 Door Drive, Mount Hope Ohio, 44660 or call 1-800-354-3643 or visit our website at: www.geniecompany.com
Keypad MUST be mounted within sight of the garage door(s) at least 5 feet above oor and clear of any moving door parts.
• Programming will not be lost during battery removal.
1. Remove battery cover and batteries. Replace if necessary.
2. Drill a 3/32” pilot hole for the top mounting screw.
3. Install included screw into pilot hole, leaving 1/8” gap between the screw head and wall.
4. Hook the slotted mount on back of keypad over the screw.
Wall
1/8"
Screw
head gap
5. Mark and drill a 3/32” pilot hole for the bottom screw and secure keypad to the wall.
(Do not over-tighten).
6. Reinstall batteries.
NOTE: Keypad will remain active for 15 seconds after a
successful entry is made. During this 15 seconds ANY key will
operate the opener.
IMPORTANT FEATURES OF THIS KEYPAD:
• An audible beep will sound with every key pressed.
• Keypad will operate, up to, 3 doors with one PIN number.
• A temporary PIN can be set for convenient non user access.
• If at any time a mistake is made while programming or operating this keypad, Press the 7 & 9 keys together
3 times. The back light will go out indicating that the keypad is immediately ready for a new entry.
CLEARING THE KEYPAD:
If, for any reason, the keypad needs to be reset to factory default, follow these steps:
1. Press and Hold the PRGM & UP/DOWN keys for 5 seconds.
2. The LED will blink twice and go out indicating the keypad is back to factory default.
3. The keypad is now ready to be programmed.
SETTING A TEMPORARY PIN:
If the keypad is to be used by, normally, unauthorized personnel (Such as a repairman) a temporary PIN can be assigned to that
personnel to gain access to the garage.
This PIN will remain active until the main set entry code is used.
1. Enter current active PIN.
2. Press PRGM key three times. (LED will turn solid indicating keypad is ready for temporary PIN)
3. Enter temporary PIN. (3-8 digits).
4. Press PGRM key one time (LED will blink twice and go out indicating a temporary PIN is set)
5. To cancel the temporary PIN. Operate the keypad/door with the original main PIN.
6. Follow the instructions below pertaining to the garage door opener to be programmed to use new PIN.
RESETTING PIN:
Once the original main PIN is changed, the keypad must be reset to the garage door opener per instructions.
1. Enter current active PIN.
2. Press PRGM key one time. (LED will turn solid indicating keypad is ready for new PIN)
3. Enter new PIN. (3-8 digits).
4. Press PGRM key one time (LED will blink twice and go out indicating a new PIN is set)
5. Follow the instructions below pertaining to the garage door opener to be programmed to use new PIN.
SECTION B - PROGRAMMING THE KEYPAD FOR DIP SWITCH TYPE OPENERS:
Program Door #1:
1. Enter the OPENER ID written in BOX A -DOOR #1.
2. Press the UP/DOWN key. (LED will go out)
3. Enter switch string written in BOX B for DOOR #1.
4. Press UP/DOWN key. (LED will blink rapidly)
5. Enter PIN.
6. Press UP/DOWN key. Opener #1 will operate.
Program Door #2:
1. Press PGRM button twice.
1. Enter the OPENER ID written in BOX A -DOOR #2.
2. Press the UP/DOWN key. (LED will go out)
3. Enter switch string written in BOX B for DOOR #2.
4. Press UP/DOWN key. (LED will blink rapidly)
5. Enter PIN.
6. Press UP/DOWN key. Opener #2 will operate.
Program Door #3:
1. Press PGRM 3 times.
1. Enter the OPENER ID written in BOX A -DOOR #3.
2. Press the UP/DOWN key. (LED will go out)
3. Enter switch string written in BOX B for DOOR #3.
4. Press UP/DOWN key. (LED will blink rapidly)
5. Enter PIN.
6. Press UP/DOWN key. Opener #3 will operate.
SECTION A - PROGRAMMING THE KEYPAD FOR LEARN CODE TYPE OPENERS:
Program Door #1:
1. Enter the OPENER ID written in BOX A - DOOR #1.
2. Press the UP/DOWN key. (LED will go out)
3. Enter PIN.
4. Press UP/DOWN key.
5. Place opener into LEARN MODE. (See placing opener into learn mode section or openers instruction manual for remote programming
instruction)
6. Enter PIN.
7. Press UP/DOWN key 3 times. Opener #1 will operate.
Program Door #2:
1. Press PGRM button two times.
1. Enter the OPENER ID written in BOX A - DOOR #2.
2. Press the UP/DOWN key. (LED will go out)
3. Enter PIN.
4. Press UP/DOWN key.
5. Place opener into LEARN MODE. (See placing opener into learn mode section or openers instruction manual for remote programming
instruction)
6. Enter PIN.
7. Press UP/DOWN key 3 times. Opener #2 will operate.
Program Door #3:
1. Press PGRM button 3 times.
1. Enter the OPENER ID written in BOX A - DOOR #3.
2. Press the UP/DOWN key. (LED will go out)
3. Enter PIN.
4. Press UP/DOWN key.
5. Place opener into LEARN MODE. (See placing opener into learn mode section or openers instruction manual for remote programming
instruction)
6. Enter PIN.
7. Press UP/DOWN key 3 times. Opener #3 will operate.
NOTICE
- ACCESS TO THE GARAGE DOOR OPENER IS REQUIRED TO RESET THE KEYPAD TO THE OPENER -
1. Enter a personal PIN. (3-8 digits)
2. Press UP/DOWN key once. (LED will turn solid indicating keypad is ready for opener ID)
PROGRAMMING STEP 2 - SETTING A PERSONAL PIN NUMBER:
STEP 3 - PROGRAMMING THE KEYPAD - Section A = Learn Type, Section B = Fixed Code Type
This keypad can be used with, up to, 3 dierent brands and types of garage door openers in any combination. Use the steps below to
program each of the 3 doors independently.
EXAMPLE:
Door #1 is a Genie® brand Intellicode® opener. Use section A - Program Door # 1
Door #2 is a LiftMaster® Purple Learn button type. Use Section A - Program Door # 2
Door #3 is an Overhead Door® brand 9 switch trinary type. Use Section B - Program Door #3
• Find the LEARN/PGRM button on the garage door opener or external receiver - shape, color or name of this button could vary by
brand.
• Most garage door openers LEARN/PGRM buttons are located under the light covers.
• For commercial or gate openers, this button may be on the circuit board of the opener. In some cases, this button could also be on
an external receiver that is mounted on or nearby the product. Consult the devices manual if needed.
PRGM
SET
RADIO
SIGNAL
LEARN
CODE
CODE
LEARN
Gate
Recievers
EXAMPLES:
PLACING OPENER INTO LEARN MODE
STEP 1-A) DETERMINE THE DOOR OPENER BRAND AND TYPE STEP 1-B) DETERMINE DOOR CODE FOR FIXED CODE OPENERS
Convert the 12 switch code:
DOOR #1
Convert the 9 switch code:
Convert the 12 switch code:
DOOR #2
Convert the 9 switch code:
Convert the 12 switch code:
DOOR #3
STEP 4) OPERATING THE KEYPAD WITH THE OPENER(S)
STEP 5) MOUNTING THE KEYPAD AND REPLACING BATTERIES
NOTE: Only use standard or alkaline AAA
batteries.
DO NOT use rechargeable batteries