Manual

Snap Lens Hinges into
slots on back of Motor Cover
60 Watts
_--_---_ maximum Push in
Lens _ Latches
@ to
close Lens
Figure 41 Install Lens Cover and Light Bulbs
A Install two 60Watt light bulbs (not included) into Light
Sockets (Figure 41):
* Rough service, ] 30 Volt bulbs are recommended.
B Install Lens into slots in Motor Cover.
C Install Genie Emergency Release Kit (GER-2) accessory,
if purchased.
Installation is now complete.
D
f
Transmitters comply with all United States and Canadian legal requirements
asof the date of manufacture. No warranty is made that they comply with all
legal requirements of any otherjurisdiction.lf transmitters are to be used in
another country, the importer must determine compliance with any local
laws and regulations which may differ from United States and Canadian
requirements prior to use.
Los transmisores cumplen con todas lasreglamentaciones legales de los
Estados Unidos y del Canada, en la fecha de fabricaci6n. Ninguna garantia
se da que cumpian con todas as reglamentaciones legales de ninguna otra
jufisdiccibn. Silos transmisores sevan a utilizar en otro pals, el importador
debe determinar sicumplen con lasreglamentadones y leyes locales que
puedan ser diferentes alas reglamentaciones de los Estados Unidos y del
Canada,antes de usar los mismos.
Les _metteurs sont conformes _ la r_glementation am_ricaine et canadienne
compter de leur date de fabrication. Aucune garantie n'est stipul_e
indiquant qu'ils sont conformes _ toutes les prescriptions ]uridiques d'autres
autorit_s. Si les _metteurs sont utilis_s dans d'autres pays, il incombe
l'importateur d'en d_terminer bur conformit_ aux loiset r_gles locales
pouvant diff_rer de cellesdes _tats-Unis et du Canada avant toute
utilisation desdits _metteurs.
Sendeger_te entsprechen allen gesetzlichen Bestimmungen in den USA und
Kanada zum Zeitpunkt der Herstellung.Wir Obernehmen keine
Gew_hrleistung for die [inhaltung aller gesetzlichen Bestimmungen in
anderen L_ndern. Sollen Sendeger_te in anderen L_ndern eingesetzt werden,
so muss der Importeur vor dem Gebrauch sicherstellen, dass die Sendeger_te
auch sokhen [okalen Bestimmungen entsprechen, welche von den
Bestimmungen der USAund Kanadasabweichen.
x@a}_lOll_xl nI_[ 9_L}E_-_°-4_--_-A_j_l__ EF_XI_---e-bC[Xt_°l
A Monthly:
• Door springs and door hardware:
- Oil door roller, bearings, and hinges using silicone
lubricant or light oil.
WARNING
Do not operate door automatically or manually if springs
are broken. Contact a Genie Factory Authorized Dealer for
service or call Customer Service at 1-800-3S-GENIE.
• Balance Door.
Closedoor.
Release Magnetic Carriage Assembly from Rail Assembly
by pulling down on Emergency Release Knob.
Raise door manually 3'- 4' and verify that door stays at
that position. SeeCheck Step 2 on page 3.
NOTE
When the door is 3'- 4' above the ground, the door
should stay open. Slight movement is acceptable. If
the door moves too much, contact a Genie Factory
Authorized Dealer for service or call Customer Service at
1-800-35-GENIE.
Reattach Magnetic Carriage Assembly to Rail Assembly:
a. Pull the Emergency ReleaseKnob toward Power Head.
b. Close door.
Contact Reverse Test.
Perform Installation Step 10 on page 21.
WARNING
If the door fails to reverse on contact with the board,
adjust the Close ForceControl as specified in Set Limit
Switches and Force Controls on page 20. Ifthe Opener
still fails, contact a Genie Factory Authorized Dealer for
service or call Customer Service at 1-800-35-GENIE.
B Yearly:
+ Wipe off old excess lubricant from Drive Screw.
+ Lubricate Drive Screw with Genie Lubricant (GLU-3)
NOTE
Use ONLY Genie Lubricant (GLU-3). Other lubricants
may damage the Opener.
GLU-3
Lubricant
FCC AND IC CERTIFIED
All devices comply with Part 15 of the FCCRules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received, includ-
ing interference that may cause undesired operation.