Use and Care Manual

KEYPAD
THE KEYPAD IS PROGRAMMED.
Optional Programming
4
A Moving Door can cause serious injury or death.
1 Keep
3 Wall Control should be mounted within sight of door, at least 5 feet above floor and clear of moving parts.
people clear of opening while Door is moving.
2 Do Not allow children to play with Wireless Keypad.
4
During programming, the Door Opener could begin to run, so stay away from the
moving Door and its parts. To keep the Door from moving, close the Door and disconnect it from the
Opener by pulling the Emergency Release Cord.
If Safety Reverse does not work properly:
1 Close Door and disconnect the opener using Emergency Release Cord.
2 Do not use Door Opener, Remote, or Wireless Keypad.
3 Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.
Atemporary PIN allows temporary access to your home by
If you have forgotten your PIN or you fear it may have fallen
into unauthorized hands, you must erase the old programming.
repair persons, meter readers, etc. while you are out, if you so desire.
FCC and IC CERTIFIED
This device complies with FCC Part 15 and RSS 210 of Industry Canada. This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the
equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Re-orient or relocate
the receiver antenna, (2) Increase the separation between the opener and receiver, (3) Connect the opener into an outlet on a circuit different from
that to which the receiver is connected, (4) Consult your local dealer.
If the Keypad backlight does not come on, this indicates the
need to replace the batteries. No programming is lost when
replacing the batteries.
+ AAA -
+ AAA -
Figure 3
Press here
to open
Polarity
markings
Battery
Cover
Covers available in: Tan-P/N 37226T, Almond-P/N 37226U, Gray- P/N 37226S and White-P/N 37226R.
1.
2. Press .
3. Enter your new PIN (3 to 8 characters).
Press, in order, 3-5-7. (This is the default PIN)
4.
Press .
PROGRAM
SET
SET
PROGRAM
Open
Travel
Button
ROUND LED
LONG LED
Close
Travel
Button
Wall
screw
head
gap
Figure 2
1"
8
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
Additional Genie® products can be ordered through your local GENIE® Professional Dealer. To
locate a dealer near you—call 800-OK-GENIE.
A. ESTABLISH A PIN
For convenience— its easier to perform programming before mounting the Keypad
ON THE WIRELESS KEYPAD:
ON THE OPENER’
S POWERHEAD
(Fig. 1)
:
ON THE KEYPAD:
1.
Press and hold on the Powerhead for 2 seconds
(the round LED turns BLUE and the OFF,
the long LED will begin flashing PURPLE).
2.
Enter your PIN.
3.
Press . LEDs will stay on steady.
4. Press again. LEDs will turn off.
5. Press again. Door opener will run.
NOTE: Pressing any key will stop and start the opener during the next 30
seconds. (It will automatically stop at the fully closed or fully open position.)
FOR HELP—CALL 800-35-GENIE, OR VISIT WWW.GENIECOMPANY.COM.
NOTE:
Rapid blinking of the red LED indicates an error.
After a few seconds the LED will turn off. Start over.
NOTE:
NO NEED TO REPROGRAM YOUR KEYPAD. The temporary PIN is
cancelled the next time your normal PIN is entered.
NOTE:
For multiple door operation—
See Wireless Keypad Instruction Sheet
B. PROGRAM DOOR
(
S
)
2.
Press .
1.
Enter your PIN.
C. OPERATING A DOOR
ON THE WIRELESS KEYPAD:
1. Erase old PIN,
• Press & hold with the for 5 seconds or
until the lights turn off.
2. Create New PIN.
• return to Steps A & B and follow instructions as before.
PROGRAM
1. Enter your Current PIN and press .
PROGRAM
2. Enter your New PIN and press . The opener will
now work with the New PIN.
1. Remove battery cover and batteries (FIG. 3).
1. Replace with same type battery. Check proper direction.
E. AUXILIARY ACTIONS
FORGOTTEN YOUR PIN?
CHANGING YOUR PIN:
1. Enter you current PIN and press 3 times.
2. Enter a temporary PIN and press .
USING A TEMPORARY PIN:
CHANGING BATTERIES:
1. Remove the battery cover and batteries (Fig. 3).
2. Drill a 1/16" pilot hole for the top mounting screw (included).
3. Install a screw into the pilot hole, leaving a 1.8" gap between
the screw head and the wall (Fig. 2).
4. Hook the keypad over the screw
head (slot on back of keypad).
5. Mark and drill a pilot hole for the
bottom screw and install screw
(do not overtighten).
6. Install batteries and cover.
D. MOUNTING KEYPAD
THE KEYPAD MUST BE MOUNTED (1) WITHIN SIGHT OF THE
GARAGE DOOR(S), (2) AT LEAST 5 FT. ABOVE THE FLOOR
AND (3) CLEAR OF ANY MOVING DOOR PARTS.
Figure 1
?
?
12