GCS545C 5.8 Amp, 4-1/2" Circular Saw Scie circulaire de 115 mm , 5,8A Sierra circular de 4-1/2”, 5,8A Operator’s Manual Manuel d’utilisation Manual del Operario 888-552-8665 TOLL FREE HELP LINE: WEBSITE: www.genesispowertools.
English SPECIFICATIONS • • • • • • • • Model: ------------------------ GCS545C Rated Power: ------------------ 120V~ /60Hz, 5.8 Amp No Load Speed: --------------- 3500 RPM Blade Size: -------------------- 4-1/2” (115mm) Arbor Size: -------------------- 3/8” (9.5mm) Cutting Capacity at 90°: -------1-11/16” (42.8mm) Cutting Capacity at 45°: -------1-1/8” (28mm) Net Weight: --------------------5.
• Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adaptor plugs in any earthed (grounded) power tools. Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
English • Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired or replaced by an authorized service center. • Turn power tool off, and disconnect the plug from the power source and/or battery pack from the power tool before making any adjustments, changing the accessories, or storing the tools. Such preventive safety measures reduce the risk of an accidental start up which may cause personal injury.
• If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in Canada) to indicate that it is acceptable for outdoor use. • Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. • Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
English • When ripping, always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance for blade binding. • Always use blades with correct size and shape (diamond vs. round) arbor holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control. • Never use damaged or incorrect blade washers or bolts. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation.
SYMBOLS SYMBOL DESCRIPTION SYMBOL DESCRIPTION V Volts A Amperes Hz Hertz Class II construction Double Insulated construction W Watts Warning symbol. Precautions that involve your safety No Load Speed To reduce the risk of injury, read Operator's Manual before using this product.
KNOWING YOUR CIRCULAR SAW English 18 6 20 11 10 14 15 4 12 3 1 19 13 2 16 5 7 9 8 10 20 11 18 15 17 FIG 1 3 12 2 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Saw Blade Lower Blade Guard Base Lower Guard Lever Dust Extraction Port Upper Blade Guard Rip Guide Vacuum Adaptor Allen Wrench for Blade Bevel Scale Bracket 11. 12. 13. 14. 15. 16. 17. 18. 19. 20.
ASSEMBLY AND ADJUSTMENTS Warning: 4-1/2” is the maximum blade capacity of your saw. Never use a blade that is too thick to allow the outer flange washer to fit properly on the spindle. Too thick a blade will prevent the blade bolt from securing the blade on the spindle. Larger diameter blades will contact the blade guards. Either situation could result in a serious accident. BLADE INSTALLATION ( FIG 2,3,4 ) • Unplug your circular saw. • Press and hold the spindle lock button (19).
English LINE-OF-CUT INDICATORS • The line-of-cut indicator notch is provided at the front of the saw base. • The left edge of the notch is used to follow a line when making a 0° cut. • The right edge of the notch is used to follow a line when making a 45° bevel cut. • Since blade thicknesses vary, it is necessary to make test cuts in scrap material, along a guideline, to determine proper alignment of the guideline within the notch to obtain an accurate cut.
caution: To make sawing easier and safer, be sure to move the tool forward in a straight line gently. Forcing or twisting the tool will result in overheating the motor and dangerous KICKBACK, possibly causing severe personal injury. It’s important to understand the correct technique for operating your saw and to learn what the correct and incorrect ways for handling your saw.
English POCKET CUTS A pocket cut is a cut that must be made inside the area of the work piece rather than starting from an outside edge and working inward. Pocket cuts can be very dangerous for the novice to attempt because of the need to manually retract the lower guard and perform a plunge cut which is potentially hazardous. • Adjust the bevel setting to zero. • Set the blade to the correct blade depth setting. • Swing the lower blade guard up by using the lower blade guard lever.
ACCESSORIES Recommended accessories for this tool: Image Description Appliaction GACSB451 24 Teeth TCT Premium Saw Balde For cutting wood, plastic and other soft materials GACSB452 60 Teeth HSS Saw Balde For cutting drywall, wood, aluminum and other non-ferrous thin sheet metal GAPCS203 Rip cutting track system English Model # • Make super accurate rip cuts up to 48" • Add addtional tracks for even longer cuts MAINTENANCE CLEANING Avoid using solvents when cleaning plastic parts.
English TWO-YEAR WARRANTY This product is warranted free from defects in material and workmanship for 2 years after date of purchase. This limited warranty does not cover normal wear and tear or damage from neglect or accident. The original purchaser is covered by this warranty and it is not transferable. Prior to returning your tool to store location of purchase, please call our Toll-Free Help Line for possible solutions. THIS PRODUCT IS NOT WARRANTED IF USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.
Richpower Industries, Inc. 736 Hampton Road Williamston, SC USA www.genesispowertools.com 2016.01.
