8V Cordless Drill/Driver Perceuse / Tournevis sans fil de 18v Taladro / Tornillador inalámbrico de 18v Operator’s Manual Manuel d’utilisation Manual del Operario GCD18BK
English 18V Cordless Drill/Driver Operator’s Manual Specifications: • • • • • • Model: Charger Input: Motor: No-Load Speed: Chuck Size: Torque Settings: GCD18BK 120 V~ 60 Hz 18 V DC 0-550 RPM 3/8” (10mm) 16 Includes: 1 -Battery, Charger, 13-Piece Drill/Driver Bit Set, and Storage Case WARNING: To reduce the risk of injury, user must read and understand this operator’s manual before operating this tool. Save this Manual for future reference.
SAVE THESE INSTRUCTIONS WORK AREA SAFETY: • Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. English WARNING: READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT.
English • Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying power tool with your finger on the switch or plugging in power tools that have the switch on invites accidents. • Remove any adjusting keys or wrenches before turning the power tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal injury. • Do not overreach. Maintain proper footing and balance at all times.
• Feed the work piece in the correct direction and speed. Feed the work • Never leave the tool running unattended, turn the power off. Do not leave the tool until it comes to a complete stop. • Never start the power tool when any rotating component is in contact with the work piece. BATTERY TOOL USE AND CARE • Ensure the switch trigger is in the off position before inserting battery pack. Inserting the battery pack into power tools that have the switch on invites accidents.
English WARNING: READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS EXTENSION CORDS Grounded tools require a three wire extension cord. Double insulated tools can use either a two or three wire extension cord. As the distance from the power supply outlet increases, you must use a heavier gauge extension cord.
• When operating the tool from an elevated position, be aware of people or • Always hold the tool firmly in your hands before switching the tool “ON”. The reaction to the torque of the motor as it accelerates to full speed may cause the tool to twist. • Wear eye and hearing protection. Always use safety glasses with side shields. Unless otherwise specified, everyday glasses provide only limited impact resistance, they are not safety glasses.
English • Do not charge battery pack when temperature is below 50 degrees F (10 degrees C) or above 104 degrees F (40 degrees C). Store tool and battery pack in a location where temperature will not exceed 122 degrees F (50 degree C). This is important to prevent serious damage to the battery cells. • Place charger on flat non-flammable surface and away from flammable materials when re-charging the battery pack.
YOUR CORDLESS DRILL/DRIVER 2 3 English 1 4 6 5 FIG 1 7 8 1. Keyless Chuck 2. Torque Ring 3. Bubble Level 4. LED Work Light 5. Trigger Switch 6. Reversing Switch 7. Magnetic Tray 8. Battery Pack UNPACKING AND CONTENT IMPORTANT: Due to modern mass production techniques, it is unlikely the tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified.
English OPERATION WARNING: To reduce the risk of serious personal injuries, read and follow all important safety warning and instructions before using this tool. NOTE: Always Check that the power supply corresponds to the voltage on the ratings plate. Charging the tool (FIG 2) • Use only the Battery Charger that is included in this kit to recharge your batteries. • Use only 120 Volt AC Power Source. • Charge your batteries fully before using the drill for the first time.
• Turn the drill on by depressing the trigger switch. • Depressing the switch further will produce more speed and torque. • Use the reversing switch (6-FIG 1) to change the direction of rotation of the drill. • The Reversing Switch has three positions: Forward, Reverse, and Off (middle). • Always check the rotation before beginning your work. LED Work Light Your tool has a built-in LED work light to illuminate the work area. When you turn on the tool, the work light will automatically turn on.
English WARNING: Forcing a drill bit, bending or twisting the bit, or failure to maintain balance in case of binding and breakthrough can result in serious personal injury. 3. Chattering or vibration may indicate you need a finer bit or higher speed. If the bit overheats or clogs, it may indicate you need a coarser bit or slower speed setting. Replace bits when they become dull. Dull bits will produce poor results and may overheat the drill. 4.
Richpower Industries, Inc. 736 Hampton Road Williamston, SC USA www.richpowerinc.