Installation Guide

ManualsBrandsGeneration Lighting ManualsLightingMedium (E26) New Construction Housing for 6" Trims - IC Rated and Airtight - 8" Tall with Quick Connects - 50 Watt

INSTALLATION INSTRUCTIONS

1) INSTALLING FIXTURE TO CEILING

Joist type ceiling: Extend bar hangers to fit between

joists. Position fixture temporarily by hammering nail-in

tabs into joists (see Drawing B), then secure

permanently with nails. Hangers should be level with

bottom of joists.

2) ELECTRICAL CONNECTION

Junction box contains two wires, a black (hot) and white

(neutral) which must be spliced to the house wires. Use

supplied quick connects to make connections (If

applicable). MAKE SURE TO CONNECT WHITE TO

WHITE

AND COLORED OR BLACK

O BLACK. After

splicing has been completed, insert wires carefully into

junction box. Connect green ground wire to green

grounding pigtail in junction box (see Drawing B).

Replace cover.

CUTTING

A HOLE

Locate the center of proposed opening on your tile or

ceiling material and mark it. Use the template provided

to draw a 6 3/8" dia. circle around the center point. Cut

along the circular line.

CAUTION: SEE WARNING INSTRUCTIONS

ON BACK BEFORE PROCEEDING

WARNING: FOR FIXTURES PROVIDED

WITH 75˚ C. OR 90˚ C. SUPPLY WIRE

WARNING ONLY (THESE WARNINGS ARE

PROVIDED ON THE LABEL AND ON THE

FIXTURE CARTON).

WARNING: RISK OF FIRE. MOST

DWELLINGS BUILT BEFORE 1985 HAVE

SUPPLY WIRE RATED 60˚ C. CONSULT A

QUALIFIED ELECTRICIAN BEFORE

INSTALLING.

2" X 8"

1/2" TO 1" THICK

CEILING MATERIAL

7 1/2"

JOIST

BAR HANGER

TAB

1128 1128QC, 11003, 11003QC, 11028, 11028QC AIR TIGHT

HOUSING FOR DIRECT CONTACT WITH INSULATION

Installation And

Safety Instruction

HC-438

041108

ill In Item Number On Carton And

ile

his Sheet F

or F

ixture Reference. ITEM#_______________

BY PASSING THE SOCKET BRACKET STOP MAY

CAUSE THE LIGHT TO CYCLE ON AND OFF OR

NUISANCE TRIP.

Title 24 - This recesses can complies with California Title

24 zero clearance insulation cover and airtight

requirements when installed with one of the manufacturer’s

certified airtight (AT) trims and installed per the

manufaturer’s safety instructions and national and local

codes. This recessed can is rated for direct insulation

cover (IC) by Underwriters Laboratory; it has been certified

airtight in accordance with ASTM E283, and it is High

Efficacy in accordance with Section 150(k) 1 of the

California 2005 Building Energy Efficiency Standards.

Depending upon the specific application, lighting controls

or occupancy sensors may also be required to meet the

requirements of California Title 24.

POWER

LEAD

GROUND

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS WARNING: FOR FIXTURES PROVIDED WITH 75˚ C. OR 90˚ C. SUPPLY WIRE WARNING ONLY (THESE WARNINGS ARE PROVIDED ON THE LABEL AND ON THE FIXTURE CARTON). CAUTION: SEE WARNING INSTRUCTIONS ON BACK BEFORE PROCEEDING WARNING: RISK OF FIRE. MOST DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60˚ C. CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING. BY PASSING THE SOCKET BRACKET STOP MAY CAUSE THE LIGHT TO CYCLE ON AND OFF OR NUISANCE TRIP.
PAGE 2
INSTALLATION INSTRUCTIONS (CONTINUED) INSTALL TRIM ASSEMBLIES Install trim by one of the following methods: TORSION SPRINGS: Squeeze the arms together and insert them into the slotted tabs on the inside of the housing. Push upward fully so springs will hold trim in place (see Diagram 1). TORSION SPRINGS SLOTTED TABS COIL SPRINGS: You must bend the slotted tabs back up out of the way (just push upward with finger). Then hook the coil springs into the slots cut into the sides of the housing (see Diagram 2).