User Manual

BATTERY PLACEMENT
As shown in the picture above, press the screwdriver forward from the
space shown, bend the tabs and separate the front cover. Insert 2 new
AAA alkaline batteries in the battery housing with the correct battery
direction. Replace both batteries at the same time. Then align the front
part of your Room Thermostat to the back and squeeze it towards the
back.
WARNING!
When the product is not used for a long period (more than 15 days),
remove the batteries. Otherwise, malfunctions that may occur would be
out of warranty.
Please throw your dead batteries into the waste bin for batteries.
RECEIVER PLACEMENT
The important things to note for the Receiver
placement is avoiding physical contact
between the Receiver and boiler, and
protecting it against materials such as
liquid,dust etc.
The devices should be placed in order to minimize the damage to the
received and transmitted signals by paying attention to the following
points;
 The devices should not be mounted on metal surfaces.
 The devices should not be installed close to electrical cables and
electronic equipment such as computers and television units.
 The devices should not be installed near large metal structures or
other building materials using fine metal meshes such as special
glass or special concrete.
 Distance between the Room Thermostat and the Receiver should not
exceed 20 meters or 2 floors.
 Receiver must be installed at least 50 cm away from the boiler.
RECEIVER SETUP
 First, shut down your boiler and your boiler's power source with all
electrical current (fuse,socket etc.)
 As shown in the connection diagram, connect one end of the boiler
connection cable to the COM and the other to the NO input.of the
Receiver.
 Connect the other ends of the cable -which you connected to the
Receiver- to room thermostat connection terminal as shown in your
boiler's user manual.
 You must first connect the Receiver power cable to the Receiver and
then to the fuse to which the boiler is connected.
 After completing the cable connection process,firstly turn on your
fuse and then your boiler.
 By pressing the Receiver's manual usage button for 2 seconds, you
should see the Orange Light blinking on the Receiver. In this way, after
making sure that the boiler is operating, press the same button again
for 2 seconds and see that the Orange LED turns off.
 Set up the Room Thermostat to pair the Receiver with the Room
Thermostat.
RECEIVER
RECEIVER LED DESCRIPTIONS
ROOM THERMOSTAT PLACEMENT
Room Thermostat needs to be placed in the room which is used most
frequently. For instance; living room or lounge. Placing the Room
Thermostat in a spot that have air circulation like entrance of a room or
side of window should be avoided. Also anywhere close to heating units
such as radiator, stove and spots which get direct sun lights would not
be suitable. Room Thermostat needs to be located above the floor
150 cm height. Few trials may be made to find the most convenient spot.
GENERAL SPECIFICATIONS
MITRA 110S RF is a wireless room thermostat. The user can adjust the
room temperature with the required temperature and get more
comfortable and economic heating.
 Precise Temperature Measurement TPI Algorithm
 Wireless Connection ON/OFF Control
MITRA 110S RF AND EQUIPMENTS
TECHNICAL DATA
Room Thermostat
Receiver
ROOM THERMOSTAT
ROOM THERMOSTAT INDICATOR LED DESCRIPTIONS
1
2 3
MITRA 110S RF
Room Thermostat
145mm / 90mm / 29.8mm
3V DC (2 x AAA alkaline battery)
o
0.1 C
o o
(5 C) – (35 C)
1 Year (2 x AAA)
o o
(-10 C) – (+50 C)
o o
(-20 C) – (+60 C)
Dimensions
Operating Current
Temperature Measurement Accuracy
Operating Temperature Range
Battery Life
Operating Temperature
Storage Temperature
ENGLISH
MITRA 110S RF USER MANUAL
Dowels and
Screws
Alkaline Battery Receiver
90mm / 90mm / 25mm
230V AC
7A (240VAC – Resistive load)
10A (120VAC – Resistive load)
o o
(-20 C) – (+60 C)
Dimensions
Operating Current
Relay NO Switching Current
Storage Temperature
Steady Red
Blinking Green
Steady Green
3 Short Orange
Blinking
Steady Orange
3 Short Green
Blinking
Blinking Orange
Blinking Red
generallife.com.tr
DIGITAL ROOM THERMOSTAT
Adjustment Knob
Indicator LED
4
1
2
3
1-Manual Operation Button:
By disabling the Receiver, it enables you
to use your boiler manually.
2-Pairing Button:
Allows to pair the Receiver with the
Room Thermostat.
3-Receiver LED Light
4-Receiver Power Cable Input
5-Boiler Connection Cable Input
5
Room Thermostat sends a close signal to the
Receiver and the heating unit stops operating.
Room Thermostat sends an open signal to the
Receiver and the heating unit starts.
Room Thermostat sends a pairing signal to the
Receiver.
If it blinks once
If it blinks twice
If it blinks three times
Receiver has power but Receiver and
Room Thermostat are not paired.
Waiting for pairing signal from Room Thermostat.
Receiver and Room Thermostat are paired.
Boiler is not operating.
Operate the boiler signal has reached to the
Receiver.
Boiler is operating.
Shut the boiler down signal has reached to the
Receiver.
Boiler is operating in manual mode.
Receiver did not get a signal from the
Room Thermostat for 22 minutes or longer and
boiler has shut down.
AAA AAA
min. 20 cm
150 cm
RECEIVER WIRING DIAGRAM
WARNING!
Operations inside the boiler or related to the electrical installation
must be carried out by persons with professional competence.
PAIRING THE ROOM THERMOSTAT AND THE RECEIVER
 Keep pressing the Receiver's pairing button for 2 seconds and see
that the LED on the Receiver is blinking green.
 Turn the Room Thermostat button to the “ ” ( pairing) symbol.
 The LED of the Room Thermostat will blink 3 times.
 If the pairing is successful, the green flashing LED on the Receiver
will be steadily lit.
 Receiver and Room Thermostat have now been synced.
TPI ROOM THERMOSTAT WORKING LOGIC
Your Room Thermostat works with the TPI algorithm in the heating
option. Room Thermostats using TPI technology predict when the
temperature of your home will rise above or below the set
temperature and turn the heating unit on and off accordingly. This
ensures that your home stays at the temperature you set without
maximum deviations up and down.
 What is TPI?
TPI technology is designed to ensure that you get the best possible
energy efficiency from your heating system. It measures and applies
the best possible timings to deliver and maintain your home at the set
temperature level.
 How does TPI work?
Thanks to the advanced artificial intelligence technology found in the
software, it adapts to the temperature change of the environment in
which it is located. By creating a general temperature map of your
home, it learns how long it takes to reach the desired room
temperature and how to maintain this temperature. In this way, it
provides minimum energy consumption by calculating how long your
heating unit should work for.
 What is the difference?
In non-TPI room thermostats, the heating unit works and stops
continuously until it exceeds the set temperature value. If the set
temperature drops below a certain amount, the heating unit will work
again. This creates greater temperature fluctuations and less energy
control. TPI Room Thermostats, on the other hand, provide higher
savings and comfort compared to On/Off room thermostats with the
advantages it has.
TPI ROOM THERMOSTAT WORKING GRAPH
COM
NO
AC
(230V)
HEATING UNIT
TEMPERATURE (ºC) Desired Temperature TPI Room Thermostat
Time
23
4