Gen-Eye USB, USBW, & USBP® Video Pipe Inspection/Location Systems Operating Instructions Your Gen-Eye USB, USBW, or USBP Video Pipe Inspection/Location System is designed to give you years of trouble-free, profitable service. However, no machine is better than its operator. Read, understand and follow all safety warnings and instructions provided with the product. Failure to follow the warnings and instructions may result in electric shock and/or serious injury.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System Electric shock resulting in death can occur if you plug this machine into an improperly wired outlet. If the ground wire is electrified, you can be electrocuted by just touching the machine, even when the power switch is off. A ground fault circuit interrupter will not protect you in this situation. Use a UL approved tester to determine if the outlet is safe. WARNING! Read and understand all instructions.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System GENERAL SAFETY RULES WARNING Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. SAVE THESE INSTRUCTIONS! Work Area 1. Keep work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System 2. Be sure that the unit is plugged into a properly grounded receptacle. If in doubt, check receptacle before plugging in machine. Check the power cord to see that there are no cuts or frays, and that the grounding prong on the plug is still in place. 3. If the power cord supplied with the machine is not long enough, be sure to use a 16 gauge heavy duty extension cord no more than 50 feet long and in good condition.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System VOICE OVER MICROPHONE BATTERY CHARGER (USBP only) This unit includes an internal microphone so you can add commentary to your videos. Press the MIC button to activate the Microphone. A light will illuminate when the Mic is "live". Press the MIC button again to MUTE the microphone. If you hear audio feedback (a screeching sound) when trying to use the microphone, it is because the volume control on the monitor is turned up too high.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System KEYBOARD/COUNTER OPERATING INSTRUCTIONS KEY FUNCTION Page Select [Page Select] followed by 1-9 recalls saved pages on-screen. Page Save Save current on-screen text to memory page. Clear Clear Screen and place cursor at home position (i.e. top left corner). Cursor ON/OFF Cursor ON/OFF toggle. SET/CLR/CNTR To set counter, press [SET/CLR/CNTR] followed by [+] or [-] and 4 digits. Press [Enter] to confirm.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System DOCKING ARM CAMERA AND REELS The Docking Arm combines the reel and monitor into one portable unit. It lets you adjust the height, axis, and angle of the Command Module to suite each inspection location. Once the Docking Arm is assembled, you can easily remove the Command Module to store the unit indoors at night or protect it in the front of your truck. To assemble the Docking Arm: 1. Place the Command Module upside down on a flat surface. 2.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System OPERATION 1. Release the reel lock and loosen the drag break on the side of the reel. 2. Slide the camera into the line. Be sure that the push rod is rated for the size pipe you are inspecting. Be careful not to force the camera around tight bends. If you see an obstruction, stop. Do not attempt to clear the pipe by using the camera head. Always use the proper tool for the job. 3.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System How to Set-Up the Wi-Fi Feature for Gen-Eye USB Camera Systems On an Apple device 1. Make sure the Command Module is turned ON and you are next to the unit. 2. On your cell phone, tablet, or other Wi-Fi enabled device, go to the App Store. NOTE: You must have an Apple account set up before proceeding. 3. Search for and download “G-Pipe Wifi Viewer”. 4. On your device, open “Settings” and select “Wi-Fi”. Make sure Wi-Fi is ON.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System How to Set-Up the Wi-Fi Feature on Gen-Eye USB Camera Systems On an Android device 1. Make sure the Command Module is turned ON and you are next to the unit. 2. On your cell phone, tablet, or other Wi-Fi enabled device, go to the Play Store (Android). NOTE: You must have a Google account set up before proceeding. 3. Search for and download “G-Pipe Wifi Viewer”. 9. You are now ready to record video or take snap shots.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System CAMERA LOCATION 1. Turn on Gen-Eye Camera system by plugging in and turning on monitor. 2. Press and hold the Hot Spot Locator On/Off button. Check battery strength on display. 3. Press MODE icon until indicator displays Sonde/Camera Head mode. 4. Press Antenna Select icon until indicator displays Total Field configuration. 5. Set Locator to 512Hz by pressing FREQ button until 512 Hz appears on display. 6.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System MAINTENANCE 2. After disconnecting the camera assembly, inspect the O-ring for any damage, and if worn, replace it with a new one. Also, when replacing any O-rings, make sure there is no dirt or grit on it, as it may not seal properly. Apply silicone grease or petroleum jelly to the O-ring for proper sealing. 3. To reconnect the camera assembly, carefully align the rear connector on the camera assembly and the push rod connector.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System ADDITIONAL MAINTENANCE TIPS No Picture, Lights OK The camera should always be cleaned and inspected after every use as dirt, grime and grease can cause unnecessary problems such as failure of the camera seals. Check Monitor power switch is ON. Check to make sure the power source is “live” (for 120 volt AC). The camera spring is attached to the cable via three (3) 4-40 x ½” stainless steel hex socket cap screws.
Gen-Eye USB, USBW, USBP® Video Pipe Inspection/Location System Bad or Grainy Picture Battery Won’t Hold Charge (SDP only) Check the camera lens for dirt, grime, scratches or other foreign matter. Allow 3 hours to fully charge battery. Check the Light Head to see if it is not supplying sufficient light due to weak, dirty, or burned out bulbs. Cold weather can reduce battery life. Keep unit warm in cold weather.