User's Manual
Table Of Contents
- Contents
- Section 1 Getting Started
- Introduction
- Unpacking Your System
- Precautions
- Checklists
- Features
- The First Time. . .
- Connecting the AC Adapter
- Installing the Battery
- Turning the Computer On and Off
- Adjusting the Volume
- Calibrating the Touch Screen
- Startup Problems?
- Section 2 Getting Familiar with Your Computer
- Introduction
- Individual Parts
- LED Activity Indicators
- LED Power / Radio Indicators
- Keyboard Basics
- Restarting the Computer
- Primary Keys
- Arrow Keys
- Function Keys
- Numeric Keypad
- Touchpad
- General Guidelines
- Scrolling Buttons
- Connecting an External Keyboard or Mouse
- Disk Drives
- The PC Card Slot
- Connecting to an External Monitor
- Section 3 Making Connections
- Making Connections
- Rear Connectors
- Left Side Connectors
- Right Side Connectors
- Section 4 If You Have a Wireless Modem
- Introduction
- Before You Start: Register!
- Registering Your Wireless Modem
- Wireless Modem LED Status
- Installing Your Wireless Modem Software
- Using Your Wireless Modem
- Section 5 Power Management
- Power Management
- Battery Calibration
- Monitoring Battery Power
- Low Battery Alarms
- Battery Charging
- Power Saving Modes
- Suspend Mode
- Initiating Suspend Mode
- Power Button Settings
- When to Replace the Battery
- Heat Considerations
- Section 6 Customizing Your Bios Settings
- Using the BIOS Setup Utility
- BIOS Setup Menu
- Starting the BIOS Setup Utility
- The Main Menu
- Navigating and Entering Information in BIOS
- Standard CMOS Setup
- Standard Feature Description
- Advanced CMOS Setup
- Power Management
- Peripheral Setup
- Auto-Detect Hard Disk
- Change Supervisor Password
- Change User Password
- Auto Configuration with Optimal Settings
- Exiting and Saving
- Section 7 Optional Equipment and Accessories
- Vehicle Adapter
- Vehicle Cradle
- PRECAUTIONS
- Charging Batteries
- Communicating with Other Devices
- Surge Protection
- Selecting the Right Surge Protection
- Selecting the Right Equipment
- Section 8 Maintenance and Storage
- Introduction
- Touch Screen Care
- Hard Drive Care and Handling
- Internal Hard Drives
- External PC Card Hard Drives
- Battery Maintenance and Storage
- Maintaining Batteries
- Storing Batteries
- Computer Maintenance and Storage
- Maintaining Your Computer
- Storing Your Computer
- Appendix A Error Messages
- Introduction
- POST Messages
- MS-DOS Messages
- Windows Messages
- Application Messages
- Appendix B Troubleshooting
- What to Try First
- For More Help
- Common Solutions to Common Problems
- Applications
- Batteries
- Cellular Modem
- Display
- Hard Disk
- I/O Ports
- Keyboard
- Landline Modems
- Miscellaneous
- Mouse
- PC Cards
- Pen/Touch Screen
- Wireless Modems
- Appendix C Glossary
- Index
98
GoBook Users Manual
77-0100-001 12 September 2000
xxxxxh Option ROM checksum failure where xxxxxh is the starting address of the option
ROM
An expansion board contains a defective ROM. Try restarting the computer by pressing CTRL+ALT+DEL. If the
problem persists, the expansion board may need to be replaced. Report this error to your supervisor or your
organization’s help desk.
-PC87570 CPU test failed! Press ENTER to continue
-PC87570 initialization failed! Press ENTER to continue
-PC87570 RAM test failed! Press ENTER to continue
-PC87570 ROM test failed! Press ENTER to continue
Restart the computer by pressing both mouse buttons for at least ten seconds and then releasing the buttons. You can
press ENTER to continue to use the computer since basic computer functions may still be operable; however, the
battery will not be charged properly. If the problem persists, contact your organization’s help desk.
MS-DOS Messages
The MS-DOS operating system may display a warning or error message if it encounters a problem with a command
in the CONFIG.SYS or AUTOEXEC.BAT file, or a command that you entered at the DOS prompt. Following are a
few of the most common MS-DOS messages.
Bad command or file name
A command was entered that is spelled incorrectly or does not exist on the computer.