User Manual
Table Of Contents
- Contents
- Section 1 Getting Started
- Introduction
- Unpacking Your System
- Precautions
- Checklists
- Features
- The First Time. . .
- Installing the Battery
- Connecting the AC Adapter
- Turning the Computer On and Off
- Adjusting the Volume
- Calibrating the Touch Screen
- Startup Problems?
- Section 2 Getting Familiar with Your Computer
- Introduction
- Individual Parts
- LED Activity Indicators
- LED Power / Wireless Modem Indicators
- Keyboard Basics
- Restarting the Computer
- Primary Keys
- Arrow Keys
- Function Keys
- Numeric Keypad
- Touchpad
- General Guidelines
- Scrolling Buttons
- Connecting an External Keyboard or Mouse
- Disk Drives
- The PC Card Slot
- Connecting to an External Monitor
- Section 3 Making Connections
- Introduction
- Rear Connectors
- Left Side Connectors
- Right Side Connectors
- Section 4 If You Have a Wireless Modem
- Introduction
- Before You Start: Register!
- Registering Your Wireless Modem
- Wireless Modem LED Status
- Installing Your Wireless Modem Software
- Using Your Wireless Modem
- Section 5 Power Management
- Power Management
- Battery Calibration
- Monitoring Battery Power
- Low Battery Alarms
- Battery Charging
- Power Saving Modes
- Suspend Mode
- Initiating Suspend Mode
- Power Button Settings
- When to Replace the Battery
- Heat Considerations
- Section 6 Customizing Your Bios Settings
- Using the BIOS Setup Utility
- BIOS Setup Menu
- Starting the BIOS Setup Utility
- The Main Menu
- Navigating and Entering Information in BIOS
- Standard CMOS Setup
- Standard Feature Description
- Advanced CMOS Setup
- Power Management
- Peripheral Setup
- Auto-Detect Hard Disk
- Change Supervisor Password
- Change User Password
- Auto Configuration with Optimal Settings
- Exiting and Saving
- Section 7 Optional Equipment and Accessories
- Vehicle Adapter
- Vehicle Cradle
- PRECAUTIONS
- Charging Batteries
- Communicating with Other Devices
- Surge Protection
- Selecting the Right Surge Protection
- Selecting the Right Equipment
- Section 8 Maintenance and Storage
- Introduction
- Touch Screen Care
- Hard Drive Care and Handling
- Internal Hard Drives
- External PC Card Hard Drives
- Battery Maintenance and Storage
- Maintaining Batteries
- Storing Batteries
- Computer Maintenance and Storage
- Maintaining Your Computer
- Storing Your Computer
- Appendix A Error Messages
- Introduction
- POST Messages
- MS-DOS Messages
- Application Messages
- Appendix B Troubleshooting
- What to Try First
- For More Help
- Common Solutions to Common Problems
- Applications
- Batteries
- Display
- Hard Disk
- I/O Ports
- Keyboard
- Landline Modems
- Miscellaneous
- Mouse
- PC Cards
- Pen/Touch Screen
- Wireless Modems
- Appendix C Glossary
- Index
71
Section 6. Customizing Your Bios Settings
77-0100-003 19 January 2001
Change Supervisor Password
A supervisor password must be set before a lower-level user password can be set. After selecting Change Supervisor
Password, press Enter. You will be prompted for the new password, and then again to verify it. Type in six or fewer
keystrokes. If you make an error, press Esc to start over.
Change User Password
With a User password, you can enter the Setup Utility and change or remove the User password, but you cannot enter
the Setup Utility and change or remove the Supervisor password, nor enable diskette access if it has been disabled.
Auto Configuration with Optimal Settings
The Auto Configuration menu resets the computer to default values. The Auto Detect Hard Disks likewise helps
users to configure their systems quickly. When you see the following prompt, choose Y to reset the computer to
default values.
Load high performance settings
(y/n)(y/n)
(y/n)(y/n)
(y/n)