User's Manual

ManualsBrandsGeneral Dynamics Broadband ManualsElectronics700 MHz TD-CDMA USB STick Modem

Wireless Broadband Modem

USB-Stick-Modem Quick Start Guide

Important Notes:

Read through the entire Quick Start Guide prior to beginning installation, paying particular

attention to Safety and Care instructions.

Run the installation software provided before connecting the USB Stick Modem to the computer.

The installation software will instruct the user when to insert the USB-Modem into the computer.

If you wish to disconnect the USB Stick Modem from the computer it is important to first make it

safe for removal. Do this by clicking on the icon in the toolbar on the lower right of the screen

and selecting STOP.

Caution:

This USB modem is approved for use in normal size laptop computers only (typically with 12

inch or larger display screens). To comply with FCC RF exposure requirements, this modem

should not be used in configurations that cannot maintain a distance of at least 5mm

(approximately 0.2 inch) from users and bystanders.

ntennae

(

internal

)

Status Indicator

SIM Card Tra

(beneath USB Connector - if fitted)

USB Connecto

(Cap removed)

Summary of content (10 pages)

PAGE 1
Wireless Broadband Modem USB-Stick-Modem Quick Start Guide Antennae (internal) USB Connector (Cap removed) Status Indicator SIM Card Tray (beneath USB Connector - if fitted) Important Notes: Read through the entire Quick Start Guide prior to beginning installation, paying particular attention to Safety and Care instructions. Run the installation software provided before connecting the USB Stick Modem to the computer.
PAGE 2
Getting Started This Quick Start Guide gives basic installation and configuration instructions. Follow the instructions on the following pages to install the USB Stick Modem client software and driver files, before connecting the modem to the computer and then perform on-line registration, if applicable. Refer to the User Guide for the complete installation, upgrade and configuration procedures. Be sure to complete each of the following steps outlined below before moving on to the next step.
PAGE 3
Step 1. Install Client Software and USB Stick Modem Drivers Follow the instructions according to your installed operating system. Where no CD is provided for installation, your service provider shall provide the client installation software and necessary drivers. Windows 2000™ You must log in with administrative privileges 1. Where a CD is provided for the installation, close any programs that may be running and insert the CD into the CD-ROM drive on your computer.
PAGE 4
Step 2. Insert the USB Stick Modem and Obtain the Best Radio Signal Fit the SIM or USIM card, if one has been provided, into the SIM slot in the USB Stick Modem, observing the correct orientation and with the gold contacts on the SIM/USIM face down. Connnect the USB Stick Modem into a USB port on your computer either directly or using the cable supplied. The Modem will draw the power it needs to operate from the computer.
PAGE 5
Step 4. Updating Operating System Patches and TCP Settings The installation software will now determine if your computer needs any official operating system patches applied or any TCP configuration settings changed. Follow the instructions on each screen to complete the upgrading of any patches or TCP settings. Step 5.Your installation is now complete The installation has completed. You will be asked to reboot your computer so that any operating system patches and TCP setting changes can be used.
PAGE 6
Additional Information When the Modem has no signal strength the Signal Quality graph will remain blank and the Connect button will not be selectable. The Modem can be disconnected using the Disconnect button when the Client Software has been restored from the task bar. Note: When only the red indicator is lit it may not be possible to open the Client Software application.
PAGE 7
Safety and Care Instructions Before using your USB Stick Modem for the first time, please read and follow all warnings, safety, care, cleaning and operating instructions on the USB Stick Modem label and in this guide. These guidelines will help protect your product from potential damage and ensure your personal safety. Safety Guidelines for the USB Stick Modem • Do not attempt to disassemble the USB Stick Modem; doing so may expose you to unsafe conditions.
PAGE 8
Exposure to Radio Frequency Signals The following information includes important safety guidelines regarding exposure to radio frequency (RF) signals and the use of electronic devices. Your modem is a low power radio transmitter and receiver. When it is ON, it receives and also sends out RF signals. The USB Stick Modem has been evaluated against the Specific Absorption Rate (SAR) limits defined by the FCC for devices of this type. The highest reported SAR value complies with the 1.
PAGE 9
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
PAGE 10
Care and Cleaning Guidelines Use a clean soft cloth, slightly moistened with water, and wipe the outside surface of the USB Stick Modem only. Do not use aerosol sprays, solvents, or abrasives when cleaning your USB Stick Modem. These items may scratch the surface or damage the interior components of the USB Stick Modem. Avoid dropping, shaking or striking the USB Stick Modem. This may damage its components. Information in this document and the products described are subject to change without notice.