OEM PCI Express Mini Module Integration OEM PCI Express Mini Module Integration Guide V01.
OEM PCI Express Mini Module Integration Contents 1 2 3 General ................................................................................................................ 3 1.1 Approvals and Dates ............................................................................................................... 3 1.2 Change Record ....................................................................................................................... 3 1.3 Acronyms ..................................
OEM PCI Express Mini Module Integration 1 1.1 General Approvals and Dates Approval Date W. J. Jones 1.2 Change Record Date Version Author 20/08/2008 01.00 PFW New Document. 23/10/2008 01.01 PFW Additional details added. 04/03/2009 01.02 PFW Updated PEM Mechanical drawing.
OEM PCI Express Mini Module Integration 1.3 Acronyms Term Definition MPE Maximum Permissible Exposure OEM Original Equipment Manufacturer PCIe PCI Express PCI SIG PCI Special Interest Group PEM PCI Express Mini SIM Subscriber Identity Module TDD Time Division Duplex UMTS Universal Mobile Telephone System USB Universal Serial Bus 1.
OEM PCI Express Mini Module Integration 2 Introduction This document describes the method of integrating the IPWireless PCI Express Mini module into an OEM product. 2.1 Scope of Document This document applies to the IPWireless PCI Express Mini module only. 2.2 Overview of Module The IPWireless PCI Express Mini module provides a complete UMTS TDD wireless modem solution and only requires to be inserted in a PCI Express Mini compliant interface and connection of external antennas.
OEM PCI Express Mini Module Integration 3 Module Connections 3.1 PCI Express Mini Interface (J1) The IPWireless PCI Express Mini module is provided with a 52 pin edge connector for connection to the external application. This connection supports the following interface types and these are described below. The pinout is shown in Annex 1. 3.1.1 Universal Serial Bus The PCI Express edge connector provides a USB 2.0 interface, this interface supports low speed (1.
OEM PCI Express Mini Module Integration 3.3 RF Connections The IPWireless PCI Express Mini module provides two RF connections for external antennas. The main port must be connected, the diversity port may or may not be connected depending upon application. The connector type is the Hirose U.FL series. Figure 2: RF Connections 3.4 DC Power The module requires a DC supply of between 3.0V to 3.6VDC with the nominal voltage being 3.3VDC, maximum input current is 950mA at 3.3VDC.
OEM PCI Express Mini Module Integration 4 Mechanical The IPWireless PCI Express Mini module is designed to be installed in a PCI Express compliant slot capable of holding an F1 full size mini card. Figure 3: PEM Module 4.1 Thermal Management The PCI Express Mini module integration shall be in accordance with the PCISIG thermal requirements.
OEM PCI Express Mini Module Integration 5 5.1 Regulatory Information Compliance with FCC Rules and Regulations The IPWireless PCI Express Mini module is certified against FCC Part 27 for operation in the 24962690MHz frequency allocation. The module is certified under FCC ID: PKTPEMAAU1 and is only certified for use with external antennas, the maximum antenna gain allowed is defined on the FCC Grant of Certification.
OEM PCI Express Mini Module Integration 6 Annex 1: PCI Express Mini Edge Connector Pinout Pin Name Pin Name 51 Reserved 52 +3.3Vaux 49 Reserved 50 GND 47 Reserved 48 +1.5V 45 Reserved 46 LED_WPAN# 43 GND 44 LED_WLAN# 41 +3.3Vaux 42 LED_WWAN# 39 +3.3Vaux 40 GND 37 GND 38 USB_D+ 35 GND 36 USB_D‐ 33 PETp0 34 GND 31 PETn0 32 SMB_DATA 29 GND 30 SMB_CLK 27 GND 28 +1.5V 25 PERp0 26 GND 23 PERn0 24 +3.
