User's Manual

P1D Wireless Broadband Modem User Manual
- Page 39 of 46 -
701 The device moved to a BPS rate not supported by the COM driver.
702 Device response received when none expected.
703 ERROR INTERACTIVE MODE
704 ERROR BAD CALLBACK NUMBER
705 ERROR INVALID AUTH STATE
706 ERROR WRITING INITBPS
707 X.25 diagnostic indication.
708 The account has expired.
709 Error changing password on domain.
710 Serial overrun errors were detected while communicating with your modem.
711 RasMan initialization failure. Check the event log.
712 Biplex port is initializing. Wait a few seconds and redial.
713 No active ISDN lines are available.
714 Not enough ISDN channels are available to make the call.
715 Too many errors occurred because of poor phone line quality.
716 The Remote Access IP configuration is unusable.
717 No IP addresses are available in the static pool of Remote Access IP addresses.
718 PPP timeout.
719 PPP terminated by remote machine.
720 No PPP control protocols configured.
721 Remote PPP peer is not responding.
722 The PPP packet is invalid.
723 The phone number, including prefix and suffix, is too long.
724 The IPX protocol cannot dial-out on the port because the computer is an IPX router.
725 The IPX protocol cannot dial-in on the port because the IPX router is not installed..
726 The IPX protocol cannot be used for dial-out on more than one port at a time.
727 Cannot access TCPCFG.DLL.
728 Cannot find an IP adapter bound to Remote Access.
729 SLIP cannot be used unless the IP protocol is installed.
730 Computer registration is not complete.
731 The protocol is not configured.
732 The PPP negotiation is not converging.
733 The PPP control protocol for this network protocol is not available on the server.
734 The PPP link control protocol terminated..
735 The requested address was rejected by the server..
736 The remote computer terminated the control protocol.
737 Loopback detected..
738 The server did not assign an address.
739 The remote server cannot use the Windows NT encrypted password.
740 The TAPI devices configured for Remote Access failed to initialize or were not installed
correctly.
741 The local computer does not support encryption.
742 The remote server does not support encryption.
743 The remote server requires encryption.
744 Cannot use the IPX net number assigned by the remote server. Check the event log.
752 A syntax error was encountered while processing a script
P1D Wireless Broadband Modem User Manual
- Page 40 of 46 -
Wireless Broadband Modem Extended Errors
Error Message Cause Recovery Action
Normal disconnect
None. This is normal and does
not indicate any error.
Network busy –
please try again later
The network is temporarily
busy.
Session establishment should be
attempted at a later time.
Network not available
– please try again
later
There is a temporary
problem with the wireless
network that is affecting all
users.
You will not be able to connect to
the Internet until your service
provider has repaired the system.
Session establishment should be
attempted at a later time.
User rejected by the
network
The network is not able to
verify who you are. This
could be due to different
problems based upon
whether or not you have a
SIM present:
1) Without SIM present
2) With SIM present
The recovery actions for the
specific causes are as follows:
1) The network does not recognize
the access identifiers that you
gave yourself when you
registered. Contact your service
provider’s technical support for
assistance.
2) Contact your service provider’s
technical support for assistance.
Service provider not
supported
This is normally seen when
attempting to establish an
internet session and gain
access to your ISP with an
invalid ISP phone number.
The ISP parameters are held in a
phonebook. To verify that these
values are correct, start up your
internet browser (for Internet
Explorer) and click on
“Tools/Internet
Options/Connections”. You should
see an entry called “ipwireless”.
To view the phonebook entry
highlight the ‘ipwireless’ entry.
Then click on the Settings button
to view the ISP username and
password.
Also click on the “Properties”
button and examine the phone
number. This must be set to *99#.