Full Product Manual
Table Of Contents
- Section 1: Safety Rules & General Information
- Section 2: General Information and Setup
- Emissions
- Remove Contents from Carton
- Attaching Tow Bar to Push Bar
- Installing Hitch
- Connecting Remote Control
- Maintenance Meter Installation
- Adding Oil
- Adding Fuel
- High Altitude Replacement Kit
- Connecting Battery Cable
- Checking Tire Pressure
- Hitching Unit to Tow Vehicle
- Attaching Blade Engage and Disengage Remote Control
- UTV Extension
- Blade Clutch Burnishing
- This page intentionally left blank.
- Section 3: Operation
- Operation and Use Questions
- Operating Parameters
- Tow Vehicle Restrictions
- Controls and Symbols
- Before Starting Engine
- Starting Engine
- Stopping Engine
- Engaging Blades
- Disengaging the Blades
- Adjusting Mower Deck Height
- Offset Mowing
- Mowing Slopes and Uneven Terrain
- If Mower Becomes Stuck
- Cutting Brush and Saplings
- This page intentionally left blank.
- Section 4: Maintenance and Troubleshooting
6 Owner’s Manual for Tow-Behind Field and Brush Mower
General Information and Setup
Emissions
The United States Environmental Protection Agency (US
EPA) (and California Air Resources Board (CARB), for
engines/equipment certified to California standards)
requires that this engine/equipment complies with exhaust
and evaporative emissions standards. Locate the emis-
sions compliance decal on the engine to determine appli-
cable standards. For emissions warranty information,
please reference the included emissions warranty. It is
important to follow the maintenance specifications in the
manual to ensure the engine complies with the applicable
emissions standards for the duration of the product’s life.
Remove Contents from Carton
1. See Figure 2-1 and Figure 2-2. Verify carton contents
prior to assembly. Carton contents should contain the
following.
Figure 2-1. Hardware Supplied in Product Package
Figure 2-2. Maintenance Meter
2. Contact Generac Customer Service at 1-888-436-
3722, or www.generac.com with the unit model
and serial number for any missing items.
3. Record model, serial number, and date of pur-
chase on front cover of this manual.
Attaching Tow Bar to Push Bar
1.
See
Figure 2-3
.
Secure offset bracket (A) to push
bar with 4.5" long clevis pin, washer, and hairpin (B).
Figure 2-3. Offset Bracket Secured to Push Bar
2.
Align hole in tow bar with hole in offset bracket and
install clevis pin, washer, and hair pin (C).
Item Description QTY
A Pin, Clevis, 1/2" OD X 4.5" LG 1
B Pin, Clevis, 1/2" X 2-1/2", TRT 2
C Key, Ignition Switch 2
D Washer, SAE Flat, 1/2", ZP 3
E Pin, Hair, 1/2" to 9/16", 12" Wire 3
F Receiver, 2”, Class II 1
G Extension, Tow Bar, Ball Hitch 1
H Chains, Safety, 36", Individual 2
I Bolt, Hex, Flange, 1/2-13 X 5" 2
J Washer, 53" ID X 1.06" OD X .095" 4
K Nut, Nylon Lock, Flanged, 1/2-13 2
L Link, Chain Threaded Connector 2
005868
A
B
C
E
D
006209
F
G
H
I
J
L
K
Item Description QTY
A Wire, 66 in 1
B Meter 1
C Mounting Bracket 1
D Cable Ties 3
E 5/16-18 x 1" Bolt, Flanged 1
F 5/16-18 Nut, Nylon Lock, Flanged 1
008072
A
D
C
B
F
E
005829
B
005869
C
B
A
(000449)
Personal injury. Install clevis pins from the bottom with the
washers and hair pins on top. Failure to do so could
result in death, serious injury, equipment or property
damage.
WARNING