Specification
10 of 14
D2.2L G22 Extended Tank (1 of 2)
4321
43 1
A
B
A
B
1495 [58.9]
OVERALL
HEIGHT
888 [35.0]
OVERALL WIDTH
365 [14.4]
TYP
197 [7.8]
TYP
2424 [95.4]
OVERALL LENGTH
1938 [76.3]
TYP
897 [35.3]
DOOR WIDTH
TYP
173 [6.8]
EXHAUST OUTLET
611 [24.0]
EXHAUST OUTLET
1029 [40.5]
CENTER OF GRAVITY
SERVICE ITEM 2.2L
OIL FILL CAP RIGHT SIDE
OIL DIP STICK RIGHT SIDE
OIL FILTER RIGHT SIDE
OIL DRAIN HOSE RIGHT SIDE
RADIATOR DRAIN HOSE LEFT SIDE
COOLANT RECOVERY BOTTLE LEFT SIDE
RADIATOR FILL CAP ACCESS ROOF
AIR CLEANER ELEMENT RIGHT SIDE
MUFFLER FRONT SIDE
FAN BELT EITHER SIDE
BATTERY LEFT SIDE
WEIGHT DATA WITH EMPTY BASETANK
(SEE NOTE 5)
GENERATOR AS SHOWN 842 [1857]
WITH WOODEN SHIPPING SKID 888 [1957]
TITLE
INSTALL PROTECTOR D2.2L G22
EXTENDED TANK
ISSUE DATE: 10/2017
SIZE CAGE NO DWG NO
10000018412
REV
B
N/A
C
SCALE
0.050
WT-KG SEE ABOVE SHEET
1 of 2
GENERAC POWER SYSTEMS OWNS THE COPYRIGHT OF THIS DRAWING
WHICH IS SUPPLIED IN CONFIDENCE AND MUST NOT BE USED FOR
ANY PURPOSE OTHER THAN FOR WHICH IT IS SUPPLIED WITHOUT
THE EXPRESS WRITTEN CONSENT OF GENERAC POWER SYSTEMS.
c GENERAC POWER SYSTEMS 2013
ELECTRONICALLY APPROVED
INSIDE WINDCHILL
DRAWING CREATED FROM PRO/ENGINEER
3D FILE. ECO MODIFICATION TO BE
APPLIED TO SOLID MODEL ONLY.
SH
1/2
REV
C
WINDCHILL VERSION
C.1
RADIATOR/EXHAUST
DISCHARGE AIR
AIR INTAKE
(BOTH SIDES)
RADIATOR/EXHAUST
DISCHARGE AIR
(BOTH SIDES)
NOTES:
1. MINIMUM RECOMMENDED CONCRETE PAD SIZE: 1194 (47") WIDE X 2261 (89") LONG.
REFERENCE INSTALLATION GUIDE SUPPLIED WITH UNIT
FOR CONCRETE PAD GUIDELINES
2. ALLOW SUFFICIENT ROOM ON ALL SIDES OF THE GENERATOR FOR MAINTENANCE
AND SERVICING. THIS UNIT MUST BE INSTALLED IN ACCORDANCE WITH CURRENT
APPLICABLE NFPA 37 AND NFPA 70 STANDARDS AS WELL AS ANY OTHER FEDERAL,
STATE, AND LOCAL CODES.
3. CONTROL PANEL / CIRCUIT BREAKER INFORMATION:
- SEE SPECIFICATION SHEET OR OWNERS MANUAL
- ACCESSIBLE THROUGH CUSTOMER ACCESS ASSEMBLY DOOR ON REAR OF
GENERATOR
4. REMOVE THE REAR TANK AND REAR ENCLOSURE COVER PANEL TO ACCESS
THE STUB-UP AREAS AS FOLLOWS:
- HIGH VOLTAGE CONNECTION INCLUDING AC LOAD LEAD CONDUIT CONNECTION
NEUTRAL CONNECTION, BATTERY CHARGER 120 VOLT AC (0.5 AMP MAX) CONNECTION.
- LOW VOLTAGE CONNECTIONS INCLUDING TRANSFER SWITCH CONTROL WIRES
5. CENTER OF GRAVITY AND WEIGHT MAY CHANGE DUE TO UNIT OPTIONS.
6. ENGINE SERVICE CONNECTIONS
OIL DRAIN: 3/8" NPT
EXHAUST OUTLET: 2" O.D.
7. BOTTOM OF GENERATOR SET MUST BE ENCLOSED TO PREVENT PEST INTRUSION AND
AND RECIRCULATION OF DISCHARGE AIR AND/OR IMPROPER COOLING AIR FLOW.
8. REFERENCE OWNERS MANUAL FOR LIFTING WARNINGS.
9. MOUNTING BOLTS OR STUDS TO CONCRETE PAD SHALL BE 5/8-11 GRADE 5
(USE STANDARD SAE TORQUE SPECS)
REFERENCE OWNERS MANUAL FOR
PERIODIC REPLACEMENT PART LISTINGS
WEIGHT: KG [LBS]
DIMENSIONS: MM [INCH]
REAR ENCLOSURE
COVER PANNEL,
SEE NOTE 4
CIRCUIT BREAKER
SEE NOTE 3
CUSTOMER ACCESS
ASSEMBLY, CONTROL
PANEL ACCESS,
BATTERY CHARGER
LOCATED WITHIN
SEE NOTE 4
REMOVABLE
STUB-UP COVER
SEE NOTE 4
REAR VIEW
LIFTING PROVISIONS (4 PLACES)
SEE NOTES 5, 8 AND CENTER
OF GRAVITY DIMENSIONS
VISE ACTION LATCH, ONE PER
DOOR, ONE LIFT-OFF DOOR ON
FRONT, RIGHT AND LEFT SIDES
LIFT DOOR PROVIDES ACCESS TO: FUEL
FILL, FUEL LEVEL GAUGE, NORMAL VENT,
INNER TANK EMERGENCY VENT, OUTER
TANK EMERGENCY VENT, OPTIONAL 90%
ALARM ASSEMBLY, OPTIONAL 5 GALLON
SPILL BOX
RIGHT SIDE VIEW
EXHAUST MUFFLER
ENCLOSED WITHIN
GENERATOR ENCLOSURE
OPEN PUNCHED
LOUVERS TYPICAL ON
BOTH SIDES OF FUEL
TANK VENTILATION
DUCT TO PROVIDE
ADEQUATE CROSS-FLOW
OF AIR VENTILATION
FUEL TANK
VENTILATION DUCT
LEFT SIDE VIEW
BATTERY 12 VOLT
NEGATIVE GROUND
REMOVE COVER FOR ACCESS
TO RADIATOR FILL CAP
INTERNAL DIVIDER PANEL
SEPARATES FUEL TANK
VENTILATION DUCT FROM
THE ENGINE, ALTERNATOR
AND EXHAUST SYSTEM
REMOVE PANEL TO
ALLOW TANK VENTS
TO TERMINATE OUTSIDE
OF THE GENERATOR
ENCLOSURE (CHECK
LOCAL AND STATE
CODE FOR
APPLICABILITY)
TOP VIEW
30 kW
installation drawings
®
Protectorâ„¢