Battery - Safety Data Sheet

PS-HTR-ST-43-E_PS-HTR-ST-43-E_Lead Acid Battery SDS Standard SDS US
Version #: 08 Issue Date: 04/01/2015 Revision Date: 08/13/2019 3 of 10
Protective
Measures to be
Taken if Material is
Released or Spilled
Stop flow of material, contain/absorb small spills with dry sand, earth, and vermiculite. Do not use
combustible materials. If possible, carefully neutralize spilled electrolyte with soda ash, sodium
bicarbonate, lime, etc. Wear acid-resistant clothing, boots, gloves, and face shield. Do not allow discharge
of un-neutralized acid to sewer. Acid must be managed in accordance with approved local, state, and
federal requirements. Consult state environmental agency and/or federal EPA.
Waste Disposal
Method
Dispose of as a hazardous waste. Dispose of in accordance with applicable local, state and federal
regulations.
7. HANDLING AND STORAGE
Handling
Unless involved in recycling operations, do not breach the casing or empty the contents of the battery.
Handle carefully and avoid tipping, which may allow electrolyte leakage. There may be increasing risk of
electric shock from strings of connected batteries. Keep containers tightly closed when not in use. If
battery case is broken, avoid contact with internal components. Keep vent caps on and cover terminals to
prevent short circuits. Place cardboard between layers of stacked automotive batteries to avoid damage
and short circuits. Keep away from combustible materials, organic chemicals, reducing substances,
metals, strong oxidizers and water. Use banding or stretch wrap to secure items for shipping.
Storage
Store batteries under roof in cool, dry, well-ventilated areas separated from incompatible materials and
from activities that may create flames, spark, or heat. Store on smooth, impervious surfaces provided with
measures for liquid containment in the event of electrolyte spills. Keep away from metallic objects that
could bridge the terminals on a battery and create a dangerous short-circuit. Room ventilation is required
for batteries utilized for standby power generation. Never recharge batteries in an unventilated, enclosed
space.
Charging:
There is a possible risk of electric shock from charging equipment and from strings of series connected
batteries, whether or not being charged. Shut-off power to chargers whenever not in use and before
detachment of any circuit connections. Batteries being charged will generate and release flammable
hydrogen gas. Charging space should be ventilated. Keep battery vent caps in position. Prohibit smoking
and avoid creation of flames and sparks nearby. Wear face and eye protection when near batteries being
charged.
Other
Follow Manufacturers Recommendations regarding maximum recommended currents and operating
temperature range. Do not overcharge beyond the recommended upper charging voltage limit. Applying
pressure or deforming the battery may lead to disassembly followed by eye, skin and throat irritation.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Occupational exposure limits
US OSHA Specifically Regulated Substances (29 CFR 1910.1001 – 1050)
Ingredient
CAS Number
Type
Value
Lead
7439-92-1
TWA
0.05 mg/m³
Lead Oxide
1309-60-0
TWA
0.05 mg/m³
Lead Sulfate
7446-14-2
TWA
0.05 mg/m³
US OSHA Table Z-1 Limits for Air Contaminants ( 29CFR 1910.1000)
Ingredient
CAS Number
Type
Value
Sulfuric Acid
7664-93-9
PEL
1 mg/m³
US ACGIH Threshold Limit Values
Ingredient
CAS Number
Type
Value
Form
Lead
7439-92-1
TWA
0.05 mg/m³
Lead Oxide
1309-60-0
TWA
0.05 mg/m³
Lead Sulfate
7446-14-2
TWA
0.05 mg/m³
Sulfuric Acid
7664-93-9
TWA
0.2 mg/m³
Thoracic Fractions
US NIOSH: Pocket Guide to Chemical Hazards
Ingredient
CAS Number
Type
Value
Lead
7439-92-1
TWA
0.05 mg/m³