Manual

1.1 UNPACKING
• Removeall packagingmaterial.
• Removeseparateaccessorybox.
• Removethe generatorfrom carton.
1.1.1 ACCESSORYBOX
Checkall contents. If any parts aremissing or damaged,locatean
authorizeddealerat 1-888-436-3722.
e
e
e
1 - Owner's Manual • 1 - Handle Assembly
1 - Liter Oil SAE 30 • 1 - Frame Foot
2 - Never-Flat Wheels • 1 - Battery Charger (electric
start only)
1 - Hardware Bag (containing the following):
• 2-Rubber Feet • 2-M8 Bolt (Long)
• 2-1/2" Axle Pins • 2-M8 Bolts (Short)
• 2-Cotter Pins • 2-M8 Acorn Nut
• 2-1/2" FlatWashers • 4-Hex FlangedM8 Nuts
• 2-Short Bolts • 2-Lock Washers
• 2-FlangeNuts (electricstart only)
1.2 ASSEMBLY
Thegeneratorrequiressome assemblypriorto using it. If problems
arise when assembling the generator,please call the Generator
Hetplineat 1-888-77LOWES.
1.2.1 ASSEMBLINGTHEACCESSORYKIT
The wheels are designed into the unit to greatly improve the
portability of the generator.
You will needthe following tools to properly install the accessory
kit.
• NeedleNosePliers
• Ratchetand a 13mm (1/2") socket
• 13mm (1/2") box wrench
NOTE:
The wheels are not intendedfor over-the-road use.
1. Refer to Figure 1 and install the Wheels as follows:
• Slidethe Axle Pinsthroughthe Wheel,1/2" FlatWasher,and Wheel
Bracketon the frame.
• Insertthe CotterPinthroughthe Axle Pinthen bendthetabs (ofthe
OotterPins) outward to lock into place.
2. Refer to Figure 1 and install the Frame Foot and Rubber
Bumpers as shown.
• Slidethe RubberBumperstuds throughthe FrameFootthen install
the Locking FlangeNuts.
• Slide the HexHeadBoltsthrough the holes in the FrameRail.
• Slide the Frame Foot onto the Hex Head Bolts then install the
Locking FlangeNuts.
3. Refer to Figure 1 and install the Handle as shown.
• Slide the long Bolts through the HandleBracketand Handle,then
install the HexNuts.
Figure 1 - Wheel & Handle Assembly
2X
i/£ _ FLAT
FRANE WASHER
COTTER
PIN
N8
NUT
AXLE PIN
1.2.2 BATTERYCABLECONNECTION(ELECTR/CSTART
ONLY)_
The unit has been deliberatelyshipped with the battery cables
disconnected.
To connectthe battery (see Figure13 for connectiondetails):
1. Cut off cable ties securing battery cables and remove red
covers from batteryterminals.
2. First,connectthe redcableto the positive (+) batteryterminal
with the bolt, lock washer andnut supplied.
3. Connect the black cable to the negative(-) battery terminal
with the bolt, lock washer andnut supplied.
4. Makesure all connectionsare secure. Slidethe rubber boots
over the terminals and connection hardware.
NOTE:
If the battery is unable to start the engine,charge it with the
12V chargerincludedinthe accessory box(see the "Charginga
Battery" section for details).
2.1 KNOWTHEGENERATOR
Read the Owner'sManual and Safety Rules before operating
this generator.
Compare the generator to Figures 2 through 4 to become
familiarizedwith the locations of variouscontrols andadjustments.
Savethis manualfor future reference.
1. 120 VoltAC,20 Amp, DuplexReceptacle- Supplieselectrical
powerfor the operationof 120Volt AC,20 Amp,single-phase,
60 Hzelectrical lighting,appliance,tool and motor loads.
2. 120/240 Volt AC, 30 Amp LockingReceptacle - Supplies
electrical power for the operation of 120 and/or 240 Volt AC,
30 Amp, single-phase, 60 Hz, electrical lighting, appliance,
tool andmotor loads.
3. Circuit Breakers(AC) - Each receptacle is provided with a
push-to-reset circuit breakerto protect the generatoragainst
electrical overload.
4. Oil Drain- Useto drainengineoil.
5. AirFilter - Filters intakeair as it is drawn into the engine.