Manual

1.1 UNPACKING
• Removeall packagingmaterial.
• Removeseparateaccessory box.
• Removethe generatorfrom carton.
1.1.1 ACCESSORYBOX
Checkall contents. If any parts aremissing or damaged,locatean
authorizeddealerat 1-888-GENERAC.
• 1 - Owner's Manual • 1 - HandleAssembly
• 1-LiterOiISAE30 • 1-FrameFoot
• 2 - Never-FlatWheels • 1 - Battery Charger(electric
start only)
• 1 - HardwareBag (containingthe following):
• 2-RubberFeet • 2-M8Bolt(Long)
• 2-1/2"AxlePins • 2-M8Bolts(Short)
• 2-CotterPins • 2-M8AcornNut
• 2-1/2"FlatWashers • 4-HexFlangedM8Nuts
1.2 ASSEMBLY
The generator requires some assembly prior to using it. If
problems arise when assembling the generator,please call the
GeneratorHetplineat 1-888-GENERAC.
1.2.1 ASSEMBLINGTHEACCESSORYKIT
The wheels are designed into the unit to greatly improve the
portability of the generator.
You will needthe following tools to properly install the accessory
kit.
• NeedleNosePliers
• Ratchetand a 13mm (1/2") socket
• 13mm (1/2") box wrench
NOTE:
The wheels are net intendedfor over-the-road use.
1. Refer to Figure 1 and install the Wheels as follows:
• Slidethe AxlePinsthroughthe Wheel,1/2" FlatWasher,and Wheel
Bracketon the frame.
• Insertthe CotterPinthroughthe AxlePinthen bend thetabs (ofthe
OotterPins) outward to lock into place.
2. Refer to Figure 1 and install the Frame Foot and Rubber
Bumpers as shown.
• Slidethe RubberBumperstuds throughthe FrameFootthen install
the Locking FlangeNuts.
• Slide the HexHeadBolts through the holes in the FrameRail.
• Slide the Frame Foot onto the Hex Head Bolts then install the
Locking FlangeNuts.
3. Refer to Figure 1 and install the Handle as shown.
• Slide the long Bolts through the HandleBracketand Handle,then
install the HexNuts.
Figure 1 - Wheel & Handle Assembly
Y_ H8 ]3r]LT
(LONG)
M8 ACORN NUT--,..,. -- -- -- L
\_ _ /_2x M8 BOLT
HANBLE _ _%, II II/ (SHORT)
.
FRAHE / 7" \ \ WASHER
FOOTJ / _ _2X COTTER
8X RUBBER FOOTJ _xPI:8
NUT
1.2.2 STARTERCONNECTION(ELECTRICSTARTONLY)
The unit has been deliberately shipped with the starter cable
disconnected.
To connect starter:
1. Locatestarter cable.
2. Pullvinyl boot backonto starter cable.
3. Removenut and washerfrom starter post.
4. Put starter cable onto post and re-installwasher and nut.
2.1 KNOWTHEGENERATOR
Read the Owner'sManual and Safety Rules before operating
this generator.
Compare the generator to Figures 2 through 4 to become
familiarizedwith the locations of variouscontrols andadjustments.
Savethis manualfor future reference.
1. 120 VoltAC,20 Amp, DuplexReceptacle- Supplieselectrical
powerfor the operationof 120Volt AC,20 Amp,single-phase,
60 Hzelectrical lighting,appliance,tool and motor loads.
2. 120/240 Volt AC, 30 Amp LockingReceptacle - Supplies
electrical power for the operation of 120 and/or 240 Volt AC,
30 Amp, single-phase, 60 Hz, electrical lighting, appliance,
tool andmotor loads.
3. CircuitBreakers(AC) - Each receptacle is provided with a
push-to-reset circuit breakerto protect the generatoragainst
electrical overload.
4. Oil Drain - Useto drainengineoil.
5. Air Filter - Filters intakeair as it is drawn into the engine.
6. ChokeKnob- Usedwhen startinga cold engine.
7. Fuel Tank- SeegeneratorSpecificationsfor tank capacity.
8. Grounding Lug - Groundthe generatorto an approvedearth
groundhere. See"Groundingthe Generator"for details.
g. Run/Step Switch - Controls the operation of the generator
(pullstart models only).
gA. Start Switch - Used to start engine from the starter motor
(electricstart modelsonly).
10. Muffler - Quietsthe engine.