Spec Sheet

16 of 18
®
D3.3L G16 132 Gal Tank (1 of 2)
Installation Drawings15 • 20 • 30 • 48 • 50 kW
Protector™
1625 [64.0]
TYP
173 [6.8]
888 [35.0]
OVERALL WIDTH
2424 [95.4]
OVERALL LENGTH
182 [7.2]
TYP
1691 [66.6]
OVERALL
HEIGHT
897 [35.3]
DOOR WIDTH
TYP
608 [23.9]
EXHAUST OUTLET
581 [22.9]
998 [39.3]
CENTER OF GRAVITY
SEE NOTE 5
SERVICE ITEM D3.3L
OIL FILL CAP LEFT
OIL DIP STICK LEFT
OIL FILTER LEFT
OIL DRAIN HOSE RIGHT
RADIATOR DRAIN HOSE RIGHT
COOLANT RECOVERY BOTTLE RIGHT
RADIATOR FILL CAP ACCESS ROOF
AIR CLEANER ELEMENT RIGHT
MUFFLER FRONT
FAN BELT EITHER
BATTERY RIGHT
WEIGHT DATA WITH EMPTY BASETANK
(SEE NOTE 5)
GENERATOR AS SHOWN 1102 [2429]
WITH WOODEN SHIPPING SKID 1147 [2529]
RADIATOR/EXHAUST DISCHARGE AIR
AIR INTAKE (BOTH SIDES)
RADIATOR/EXHAUST DISCHARGE AIR (BOTH SIDES)
REFERENCE OWNERS MANUAL FOR PERIODIC REPLACEMENT PART LISTINGS
NOTES: 1. MINIMUM RECOMMENDED CONCRETE PAD SIZE: 1194 (47") WIDE X 2718 (107") LONG. REFERENCE INSTALLATION GUIDE SUPPLIED WITH UNIT FOR CONCRETE PAD GUIDELINES 2. ALLOW SUFFICIENT ROOM ON ALL SIDES OF THE GENERATOR FOR MAINTENANCE AND SERVICING. THIS UNIT MUST BE INSTALLED IN ACCORDANCE WITH CURRENT APPLICABLE NFPA 37 AND NFPA 70 STANDARDS AS WELL AS ANY OTHER FEDERAL, STATE, AND LOCAL CODES. 3. CONTROL PANEL / CIRCUIT BREAKER INFORMATION: - SEE SPECIFICATION SHEET OR OWNERS MANUAL - ACCESSIBLE THROUGH CUSTOMER ACCESS ASSEMBLY DOOR ON REAR OF GENERATOR 4. REMOVE THE REAR TANK AND REAR ENCLOSURE COVER PANEL TO ACCESS THE STUB-UP AREAS AS FOLLOWS: - HIGH VOLTAGE CONNECTION INCLUDING AC LOAD LEAD CONDUIT CONNECTION
NEUTRAL CONNECTION, BATTERY CHARGER 120 VOLT AC (0.5 AMP MAX) CONNECTION. - LOW VOLTAGE CONNECTIONS INCLUDING TRANSFER SWITCH CONTROL WIRES 5. CENTER OF GRAVITY AND WEIGHT MAY CHANGE DUE TO UNIT OPTIONS. 6. ENGINE SERVICE CONNECTIONS OIL DRAIN: 3/8" NPT EXHAUST OUTLET: 2" O.D. 7. BOTTOM OF GENERATOR SET MUST BE ENCLOSED TO PREVENT PEST INTRUSION AND AND RECIRCULATION OF DISCHARGE AIR AND/OR IMPROPER COOLING AIR FLOW. 8. REFERENCE OWNERS MANUAL FOR LIFTING WARNINGS. 9. MOUNTING BOLTS OR STUDS TO CONCRETE PAD SHALL BE 5/8-11 GRADE 5 (USE STANDARD SAE TORQUE SPECS)
WEIGHT: KG [LBS] DIMENSIONS: MM [INCH]
REAR VIEW
REAR ENCLOSURE COVER PANEL SEE NOTE 4
CIRCUIT BREAKER SEE NOTE 3
CUSTOMER ACCESS ASSEMBLY, CONTROL PANEL ACCESS, BATTERY CHARGER LOCATED WITHIN SEE NOTE 4
REMOVABLE STUB-UP COVER SEE NOTE 4
RIGHT SIDE VIEW
LIFTING PROVISION (4 PLACES)
SEE NOTES 5, 8 AND CENTER
OF GRAVITY DIMENSIONS
VISE ACTION LATCH, ONE
PER DOOR, ONE LIFT-OFF
DOOR ON FRONT, RIGHT
AND LEFT SIDES
LIFT-OFF DOOR PROVIDES ACCESS TO: FUEL
FILL, FUEL LEVEL GAUGE, NORMAL VENT,
INNER TANK EMERGENCY VENT, OUTER TANK
EMERGENCY VENT, OPTIONAL 90% ALARM
ASSEMBLY, OPTIONAL 5 GALLON SPILL BOX
LEFT SIDE VIEW
EXHAUST MUFFLER
ENCLOSED WITHIN
GENERATOR ENCLOSURE
OPEN PUNCHED
LOUVERS TYPICAL ON
BOTH SIDES OF FUEL
TANK VENTILATION
DUCT TO PROVIDE
ADEQUATE CROSS-FLOW
OF AIR VENTILATION
FUEL TANK
VENTILATION
DUCT
TOP VIEW
BATTERY 12 VOLT NEGATIVE GROUND
REMOVE PANEL TO ALLOW TANK VENTS TO TERMINATE OUTSIDE OF THE GENERATOR ENCLOSURE (CHECK LOCAL AND STATE CODE FOR APPLICABILITY)
INTERNAL DIVIDER PANEL SEPARATES FUEL TANK VENTILATION DUCT FROM
THE ENGINE, ALTERNATOR AND
EXHAUST SYSTEM
REMOVE COVER FOR ACCESS TO RADIATOR FILL CAP