Twin Sun 1 × 2 BI-COLOR SOFT LED PANEL USER MANUAL
THANK YOU FOR CHOOSING GENARAY Twin Sun INTRODUCTION The Genaray Twin Sun LED light fixture provides photographers and videographers with extremely bright yet soft continuous light. This 1 × 2-foot fixture can operate on AC or battery power, and it features flicker-free light that’s ideal for shooting video at high frame rates (slow motion).
PRECAUTIONS · Keep this unit away from water and any flammable gases or liquids. · Make sure the unit is powered off when plugging it into a power source. · Use only the correct, recommended voltage. · Handle the unit with care. · Do not attempt to disassemble or repair the equipment—doing so will void the warranty, and Genaray will not be responsible for any damage. Precautions · Please read and follow these instructions and keep this manual in a safe place.
Barndoors Barndoor locking tabs PRODUCT OVERVIEW Yoke LED array / Soft panel Locking knob Baby receiver/ Junior pin 4 Twin Sun 1 × 2 Bi-Color Soft LED Panel - USER MANUAL
Gel clips Battery status indicator Tilt adjustment knob Product Overview D-tap output power socket Battery plate V-mount release button Fan Fan on/off switch 4-pin XLR power socket DMX output connector DMX input connector Dimmer/DMX dial Power switch Color temperature dial Brightness Color temperature DMX address LCD screen Twin Sun 1 × 2 Bi-Color Soft LED Panel - USER MANUAL 5
CONTENTS INCLUDE · LED with yoke · AC power supply Contents · 3-pin DMX cable · Power cord · Barndoors · User manual 6 Twin Sun 1 × 2 Bi-Color Soft LED Panel - USER MANUAL MOUNTING THE TWIN SUN Mount the Twin Sun on any heavy-duty light stand or C-stand with a 5/8-inch baby pin and turn the locking knob until secure. Remove the locking knob to mount the Twin Sun into a 11⁄8-inch junior receiver. Important The Twin Sun and yoke weigh almost 20 lb. Make sure your light stand can support that weight.
POWERING THE TWIN SUN USING THE TWIN SUN WITH AC POWER Connect the AC power supply to the Twin Sun, and plug it into an outlet. The AC power supply has an integrated V-mount that fits into the Twin Sun’s battery plate. Align the power supply with the V-mount plate, and slide it into the mount until it clicks. Remove the AC power supply by pressing the V-mount release button and sliding the adapter off of the battery plate. USING THE TWIN SUN WITH BATTERY POWER The Twin Sun is powered by two 14.
OPERATING THE TWIN SUN The battery status indicator on the rear panel displays the remaining battery power. Instructions 8 4 lights (green) 80% to 100% 3 lights (green) 50% to 80% 2 lights (green) 30% to 50% 1 light (green) 10% to 30% 1 light (orange) Less than 10% (the light will not operate) Twin Sun 1 × 2 Bi-Color Soft LED Panel - USER MANUAL USING THE BARNDOORS To remove the barndoors, push up on the top barndoor locking tabs to release the frame.
Open the barndoors, and power on the Twin Sun. The LCD screen will display the previous settings. After powering on the Twin Sun, set the brightness and color temperature by rotating the dials on the back of the fixture. Note When the fan is turned off, the maximum brightness will be capped at 80%. Instructions ADJUSTING BRIGHTNESS AND COLOR TEMPERATURE · If the brightness is set over 80%, it will drop to 80% when the fan is turned off.
USING DMX Instructions The Twin Sun supports DMX-512 so the light’s settings can be remotely controlled from a DMX lighting control console. Important Do not use a 3-pin XLR microphone cable to connect DMX devices. Use only cables that are made specifically for DMX devices. Substituting a microphone cable can cause data transmission problems in your DMX setup. To setup DMX operation, follow these steps: 1. Use a 3-pin XLR cable to connect a DMX controller to the Twin Sun DMX input connector. 2.
Beam Angle: 120° CONNECTORS Color Temperature: 3200 to 5600 K (±300 K) Battery Plate: V-mount (×2) Color Accuracy Standard: CRI: 97, TLCI: 98 Power Input Connector: 4-pin XLR Cooling System: Fan DMX Connector: In: 3-pin XLR Out: 3-pin XLR Dimming: 10% to 100% (stepped 1% increments) Display: LCD screen Rectangular Panel Size: 14.9 × 24.7 × 4 in. (37.8 × 62.8 × 10.2 cm) Fixture Dimensions (with yoke): 20.9 × 28.9 × 4 in. (53.2 × 73.5 × 10.2 cm) Fixture Weight (with yoke): 19.6 lb. (8.
ONE-YEAR LIMITED WARRANTY This Genaray product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
