SpectroLED SP-LR2 USER MANUAL
Thank you for choosing Genaray. SpectroLED INTRODUCTION The Genaray Beacon is a lightweight and portable wand-style LED light that casts a soft wraparound beam for creative light angles and effects. The Beacon is tripod mountable or handheld, and it offers the freedom to move around your subjects to create artistic accent, hair, or rim lighting. The 312-LED array provides a hefty 1340 lumens of 5600 K daylight-balance light, and a tungsten filter is included for a warmer 3200 K color tone.
KEY FEATURES · User-replaceable 4400 mAh lithium-ion rechargeable battery · IP65 water-resistance rating— can be used in rain or other wet conditions · Optional barndoor attachment available · 5600 K daylight-balance light · 2.
Top cover Tungsten filter Power/Mode button Up button Remote indicator Battery/Channel indicator PRODUCT OVERVIEW Down button Daylight panel Battery compartment cover AC/DC socket cap AC/DC socket 1/4 in.
· Please read and follow these instructions, and keep this manual in a safe place. · Do not stare directly at the lights when they are powered on. · Keep this unit away from water and all flammable gases or liquids. · Keep this unit away from children. · Do not attempt to disassemble or repair this equipment—doing so will void the warranty, and Genaray will not be responsible for any damage. · Handle the unit with care. PRECAUTIONS PRECAUTIONS · Clean the unit with a soft, dry cloth.
INSTALLING THE BATTERY 1. Remove the battery compartment cover. INSTRUCTIONS 2. Insert the battery so the contacts are facing down into the compartment. 3. If the bottom of the battery is not flush with the bottom edge of the battery compartment, turn the battery until it’s properly seated. 4. Replace the battery compartment cover. 6 SpectroLED - USER MANUAL CHARGING THE BATTERY With the battery installed, plug the power cord into the Beacon’s AC/ DC socket and into an AC outlet.
POWERING THE BEACON Battery Power: When using battery power, the four LED indicators on the handle indicate remaining battery charge in 25% increments. The battery will last approximately 1.5 hours on a full charge with the light at full power. Turning the Beacon On or Off: To power on, press and hold the power button until the fixture illuminates, and release the power button. To power off, press and hold the power button for approximately 2 seconds, and then release it.
MOUNTING THE LIGHT INSTRUCTIONS The Beacon has a 1/4 in. threaded mount on the bottom of the light. To attach the fixture to a tripod or light stand, place the mount onto a compatible stud, and turn the light clockwise until tight and secure. The Beacon can also be used as a handheld device by grasping the base of the fixture.
The Beacon offers two color temperature modes. 5600 K DIMMING THE LIGHT The Beacon has a 100% to 10% dimming range. To adjust the light output, press and hold the up or down buttons. INSTRUCTIONS COLOR TEMPERATURE MODES Daylight balance (5600 K) produces a soft, natural color tone on subjects. For daylight balance, make sure to remove the tungsten filter. 3200 K When the tungsten filter is inserted over the wand, the Beacon produces 3200 K (tungsten balance) light.
OPERATING MODES INSTRUCTIONS The Beacon has four operating modes: constant, quick strobe (5 flash/sec.), SOS, and slow strobe (2 flash/sec.). The Beacon powers on in constant mode. Press the Power/Mode button repeatedly to cycle through the four operating modes. Note 10 Quick strobe, SOS, and slow strobe modes automatically operate at 100% brightness. The dimmer buttons are inactive in these flash modes.
REMOTE OPERATION Channel Selection: 1. Power on the Beacon. 3. Use the up/down buttons to select a channel, 1 through 4. The number of blinking LEDs indicates the channel number. INSTRUCTIONS The Beacon’s brightness can be controlled by the Genaray 2.4 GHz Wireless Remote (MB-WRT, available separately). The integrated receiver has four channels so you can control several Beacon fixtures from a single remote. 4. Press the Power/Mode button to confirm the channel selection.
REMOTE OPERATION Remote Power Adjustment INSTRUCTIONS Refer to the Genaray Remote’s user manual for information on channel and operation mode selection. To adjust the Beacon’s brightness from the remote, follow these steps: 1. Make sure the Beacon is in constant mode. 2. On the remote, select a channel, 1 through 4. Make sure the remote’s channel matches the Beacon’s channel. 3. Set the remote to Power Output mode. 4. Press and hold the remote’s + and – buttons to adjust the Beacon’s brightness.
REMOTE OPERATION Sleep Mode INSTRUCTIONS To preserve battery life, sleep mode can be activated via the remote while the Beacon is in any of the four operating modes. To put the Beacon to sleep, follow these steps: 1. Make sure the Beacon and the remote are set to the same channel 2. Set the remote to Power Output mode 3. Press and hold the power button until OF appears on the display. The LED array will turn off.
PRODUCT SPECIFICATIONS SPECIFICATIONS 14 LED Count: 312 Mount: 1/4 in. Color Temperature: 5600 K or 3200 K Input: 100 to 240 V, 50/60 Hz Dimming: 100% to 10% Battery: Lithium-ion 7.4 V, 4400 mAh Watts: 15 Battery Life: 1.5 hr. Lux: 1340 Lux @ 1 m Height: 22 in. (55.8 cm) CRI: 95.2 Diameter: 2.3 in. (6 cm) LED Life: 30,000 hr. Weight: 2 lb. (0.
ONE-YEAR LIMITED WARRANTY This GENARAY product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
