PortaSun Series RBF-20 20 IN.
THANK YOU FOR CHOOSING GENARAY PortaSun Series INTRODUCTION 2 The Genaray RBF-20 flexible LED is a unique lighting solution for photographers on the go. The feather-light 20-inch diameter array features a 672-count of daylight and tungsten LEDs that provide up to 500 lumens of bicolor light. The LED array mounts onto a light stand or tripod with its included X-bracket and ballhead mount. But it’s also designed with rings and touch-connect strips so it can hang on a wall or a picture hook.
PRECAUTIONS · Keep this unit away from water and any flammable gases or liquids. · Make sure the unit is powered off when plugging it into a power source. · Use only the correct, recommended voltage. · Handle the unit with care. · Do not attempt to disassemble or repair the equipment. Doing so will void the warranty, and Genaray will not be responsible for any damage. Precautions · Please read and follow these instructions, and keep this manual in a safe place.
Front RBF-20 OVERVIEW Flexible LED array Touch-connect strip 4 PortaSun Series 20 in.
Back Bracket attachment sleeves Product Overview X-bracket X-bracket locking knob 4-pin power cord Ballhead Ballhead tension knob Locking knob Rings 5/8-inch receiver PortaSun Series 20 in.
Controller LCD Screen Color temperature Color : 5000K Bright: 100% AC RBF-20 OVERVIEW Brightness Battery power/ AC indicator Tungsten LED brightness (WW) WW:100% : CW:100% : Daylight LED brightness (CW) 6 PortaSun Series 20 in.
Controller Hanging tabs Product Overview Battery plate V-mount release LCD screen 4-pin controller cord Brightness knob Color temperature knob/ Mode button 3-pin power input On/off switch PortaSun Series 20 in.
CONTENTS INCLUDE · Flexible LED array · Controller Contents · Power adapter · AC power cord · X-bracket · V-mount strap · Safety cable · Softbox · Diffuser ASSEMBLING AND MOUNTING THE RBF-20 1. Spread the arms of the X-bracket so they form right angles, and tighten the bracket locking knob until secure. 2. Place the LED facedown on a soft surface. 3. Fit each bracket arm into the corresponding bracket sleeves on the back of the light.
USING THE RBF-20 WITHOUT THE BRACKET 5. Tighten the locking knob until secure. Use the rings on the back of the light to hang the light on a nail or picture hook. Instructions 4. Loosen the locking knob, and place the light and bracket assembly onto a light stand with a 5/8-inch stud. Alternatively, use the touch-connect strips on the outside of the bracket sleeves to attach the light to another touch-connect strip on a wall or other surface. PortaSun Series 20 in.
POWERING THE RBF-20 AC POWER Instructions Important The RBF-20 is a multivoltage fixture capable of running on 100 to 240 V, 50/60 Hz. The included cable has a 120 V, 50 Hz. To use this fixture with other voltages, you must use a plug adapter (sold separately). 1. Use the AC power cord to connect the AC adapter to an outlet. 2. Align the 3-pin connector with the controller’s power input. Make sure the notches on the connectors match up.
MANUAL MODE In auto mode, the levels of the daylight and tungsten LEDs adjust automatically as the color temperature changes. In manual mode, the brightness level of the daylight and tungsten LEDs can be adjusted independently. When it’s first powered on, the RBF-20 defaults to auto mode. Press the color temperature button. The LCD switches to the manual mode screen. ADJUSTING THE COLOR TEMPERATURE AND BRIGHTNESS · The tungsten LED’s brightness level (WW) is controlled by the color temperature knob.
ATTACHING THE DIFFUSER 1. Remove the diffuser from its carry pouch, and unfold it. Instructions 2. Press the diffuser’s touch-connect fabric to the touch-connect strip on the edge of the light. 3. Close any gaps along the edge of the diffuser to prevent light spill. 12 ATTACHING THE SOFTBOX, DIFFUSER, AND GRID 1. Form a ring with the softbox, putting the silver material on the interior, and press the touch-connect strips together. 2.
4. Attach the diffuser to the wide touch-connect strip around the interior of the softbox. 5. Attach the grid by pressing its touchconnect fabric to the touch-connect strip around the interior of the softbox. Instructions 3. Adjust the softbox to close any gaps in the connection and prevent light spill. Note: If you plan on using the grid with this setup, attach the diffuser to the inner portion of the touch-connect strip to leave room for the grid. PortaSun Series 20 in.
PRODUCT SPECIFICATIONS Specifications LIGHT FIXTURE Expected Lamp Life: 50,000 hr. LED Count: 672 (336 Daylight, 336 Tungsten) Dimensions (H × W × D): Light: 20.5 in. (51.5 cm) outer diameter Softbox : 5.3 in. (13.5 cm) depth Controller: 2 × 8 × 3.9 in. (5.1 × 20.3 × 10 cm) Power adapter: 1.5 × 2.75 × 6.75 in. (3.8 × 7 × 17.1 cm) Output Power: 150 W Beam Angle: 120° Color Temperature: 2750 to 6500 K Color Accuracy Standard: CRI: 95 TLCI: 96 Cooling System: None Weight: LED only: 1 lb. (453.
POWER Battery Plate: V-mount AC Input Power: 100 to 240 V AC, 50/60 Hz Power Input Connector: 4 pin DC Input Power: 12 V, 15 A DC DMX Connector: No Power Source: AC adapter, V-mount battery Service Connector: No Max Power Consumption: 150 W MOUNTING Power Pass-Thru: None Specifications CONNECTORS Fixture Mount: 5/8 in. receiver MOUNTING BRACKET Bracket Material: Metal Bracket Type: X-bracket Tilt: 180° PortaSun Series 20 in.
ONE-YEAR LIMITED WARRANTY This Genaray product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
