ML-33K Endeavor 150-WATT DAYLIGHT LED MONOLIGHT USER MANUAL
THANK YOU FOR CHOOSING GENARAY Endeavor INTRODUCTION The Genaray Endeavor 150-watt monolight features an advanced chip-on-board (COB) LED that outputs a powerful constant light source to deliver a brilliant daylight-balance beam for video and photo shoots. The fixture’s natural-looking 5600 K daylight-balance light is dimmable from 100% to 0% in 10% increments for the brightness your exposures need.
PRECAUTIONS · Keep this unit away from water and any flammable gases or liquids. · Make sure this unit is powered off when plugging it into a power source. · Use only the correct, recommended voltage. · Handle the unit with care. · Do not attempt to disassemble of repair the equipment. Doing so will void the warranty, and Genaray will not be responsible for any damage. Precautions · Please read and follow these instructions, and keep this manual in a safe place.
Light Fixture - Front Bowens mount release button Bowens mount PRODUCT OVERVIEW COB LED array Reflector Umbrella locking screw Umbrella hole DC power socket Light stand mount Tilt lock Locking knob Locking button 5/8 in.
Light Fixture - Back Battery status Channel indicator Group indicator Color temperature Display Channel button Group button Power switch Adjustment dial Fuse Power socket Endeavor 150-Watt Daylight LED Monolight - USER MANUAL 5 Product Overview Brightness
MOUNTING THE ENDEAVOR CONTENTS INCLUDE · Endeavor 150-Watt LED Monolight · 7 in. reflector Contents · Tungsten filter · Power cord · User manual To mount the Endeavor on any heavyduty light stand with a 5/8-inch pin: 1. Loosen the locking knob so it doesn’t obstruct the receiver. 2. Press and hold the locking button, place the fixture over the baby pin, and release the locking button. 3. Tighten the locking knob until the light is secure.
FROM AN AC OUTLET WITH DC POWER Warning! The Endeavor is a powerful light. Do not look directly into the light when it’s powered on. The Endeavor can be powered by V-mount batteries, using the Genaray BA-VMOUNT dual-battery adapter (available separately). Connect the AC power cable to the Endeavor and to an AC outlet. Dual 14.8-volt, 160-watt-hour V-mount batteries will power the Endeavor for approximately one hour. Turn on the power switch.
OPERATING THE ENDEAVOR Instructions ATTACHING THE REFLECTOR ATTACHING AN UMBRELLA The Endeavor includes a 7-inch reflector and is compatible with Bowens-mount accessories. To attach the reflector: 1. Make sure the reflector’s umbrella pass-through is aligned with the umbrella mount. 1. Insert the three mounting studs into the notches on the fixture. 2. Insert the umbrella’s shaft through the umbrella pass-through, and then through the umbrella mount. 2.
Note Other brands’ Bowens-style reflectors will work with the Endeavor. Make sure the reflector has a pass-through hole to use it with an umbrella. SETTING THE CHANNEL AND GROUP ADJUSTING THE BRIGHTNESS Press the channel button (CH). The channel will be highlighted on the screen. Use the adjustment knob to select a channel from 1 to 16. The adjustment knob controls the brightness from 100% to 0% in 10% increments.
PRODUCT SPECIFICATIONS Specifications LED Chip Type: COB Working Voltage: 90 to 240 V AC, 50/60 Hz Color Temperature: 5600 K ±200 K Mount: 5/8 in. Light Intensity @ 3 ft.: 33,000 lx Channels and Groups: 16 channels, 5 groups (A, B, C, D, E) Dimming: 100% to 0% CRI: 97.5 Dimensions (H × D × W): 9.8 × 16.8 × 7 in. (24.9 × 42.7 × 17.8 cm) with mount and reflector TLCI: 98.5 Weight: 6 lb. (2.
ONE-YEAR LIMITED WARRANTY This Genaray product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
GG1
