CR-7D CRUX USER MANUAL Crux Daylight LED - USER MANUAL 1
Thank you for choosing Genaray. The Crux 7-inch round LED is a compact and lightweight Crux Daylight LED INTRODUCTION LED array that emits 1490 lux (@ 0.5 m) of flickerfree, continuous light. It draws only 19 W to deliver the equivalent output of a 150 W tungsten bulb. This light fixture produces a 60° beam that’s ideal for interviews and tabletop photography, as well as other applications where it’s necessary to place the lights close to your subjects.
INTRODUCTION 100% to 10% brightness. A built-in diffuser softens the light emitted by the 90-LED array, and it eliminates the multiple shadows that are often associated with LED lighting. The light generates minimal heat, and it allows you to place the fixture close to heat-sensitive subjects, like models, animals, or food, without causing discomfort or damage.
CONTENTS INCLUDE CONTENTS 4 · Genaray Crux 7-Inch Round Daylight LED with Yoke · Battery charger with power cord · Sony NP-F battery type · Carry case Crux Daylight LED - USER MANUAL · AC adapter with power cord
· Please read and follow these instructions, and keep this manual in a safe place. · Handle the unit with care. · Keep this unit away from water and any flammable gases or liquids. · Clean the unit with only a soft, dry cloth. · Make sure the unit is powered off when plugging it into a power source. · Keep this unit away from children. · Use only the correct, recommended voltage.
Front diffuser (not removable) PRODUCT OVERVIEW Tilt locking knob Locking knob 6 Crux Daylight LED - USER MANUAL 5/8 in.
Battery release button Battery indicator PRODUCT OVERVIEW Brightness control Battery contacts DC power input Power switch Crux Daylight LED - USER MANUAL 7
MOUNTING THE LIGHT INSTRUCTIONS 1. Loosen the locking knob, and insert the 5/8-inch receiver over a light stand’s 5/8-inch stud. Tighten the locking knob until secure. 2. Adjust the angle of the light, and tighten the tilt locking knob. INSTALLING THE BATTERY (OPTIONAL) Make sure the power switch is in the OFF position. 1. Align the battery terminals on the battery with the contacts in the battery mount. 2.
1. Insert the battery into the battery charger. 2. Plug the charger’s power cord into a wall socket. The LED indicator will glow red when the battery is charging. When the LED indicator turns green, the battery is fully charged. Remove it from the charger, and insert it into the light’s battery mount. CONNECTING THE POWER CORD The CR-7D LED will operate on AC power, even if the battery is not installed. INSTRUCTIONS CHARGING THE BATTERY Make sure the power switch is in the OFF position. 1.
OPERATING THE LIGHT 1. Turn the power switch ON. INSTRUCTIONS 2. Adjust the brightness with the dimmer knob.
LED count: 90 AC operating voltage: 100 to 240 V, 50/60 Hz Color temperature: 5600 K (±200 K) DC operating voltage: 9 V DC, 3 A Dimming: 100% to 10% Bulb life: 30,000 hr. Luminance: 1490 lx @ 0.5 m Battery: Sony NP-F battery type Coverage: 60° @ 0.5 m AC cable length: 9.5 ft. (2.9 m) CRI: 93 DC cable length: 3.9 ft. (1.2 m) Electrical consumption: 19 W Weight: 1.55 lb. (703 g) Tungsten output equivalent: 150 W Dimensions (W × H × D): 11.4 × 10.6 × 2 in.
ONE-YEAR LIMITED WARRANTY This GENARAY product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
