Radiance 230-WATT DAYLIGHT LED MONOLIGHT USER MANUAL
THANK YOU FOR CHOOSING GENARAY Radiance INTRODUCTION The Genaray 230-watt Radiance monolight features an advanced chip-on-board (COB) array that outputs a substantial 23,000 lux for a powerful, flicker-free 5600 K light source. Extremely quiet cooling fans make the Radiance a great a choice for film, broadcast, and video projects, as well as photo sessions. The Radiance runs on AC power or two V-mount batteries that will provide enough power for lengthy location shoots.
PRECAUTIONS · Keep this unit away from water and any flammable gases or liquids. · Make sure the unit is powered off when plugging it into a power source. · Use only the correct, recommended voltage. · Handle the unit with care. · Do not attempt to disassemble or repair the equipment. Doing so will void the warranty, and Genaray will not be responsible for any damage. Precautions · Please read and follow these instructions, and keep this manual in a safe place.
Light Fixture - Front COB LED array PRODUCT OVERVIEW Reflector Bowens mount release Locking button 4 Radiance 230-Watt Daylight LED Monolight - USER MANUAL
Product Overview Light Fixture - Back Tilt adjustment knob Yoke Locking knob 5/8 in.
Power Supply - Top Channel/ID adjustment buttons Channel/DMX ID Product Overview Color temperature Brightness Color temperature up/down buttons (bicolor fixtures only) Brightness up/down buttons V-mount battery slots LCD screen Dimmer knob 6 Radiance 230-Watt Daylight LED Monolight - USER MANUAL
Power Supply - Right Side Remote Product Overview DMX in and out ports Color temperature DC power cable Antenna port Power socket Brightness Channel/DMX ID Brightness up/down buttons Power button Power switch I - DC power O - Off II - AC power Battery power and charging indicators Radiance 230-Watt Daylight LED Monolight - USER MANUAL 7
MOUNTING THE RADIANCE CONTENTS INCLUDE · LED with yoke · AC power supply Contents · AC power cord · Remote · Antenna · Reflector · Carry case Mount the Radiance on any heavy-duty light stand with a 5/8-inch baby pin. 1. Loosen the locking knob, and press the locking button to fit the 5/8-inch mount on the light stand’s mounting stud. 2. Make sure the mount is properly seated on the light stand, and turn the locking knob until secure.
The Radiance is outfitted with a Bowens mount that’s compatible with most Bowens-mount accessories. 1. Align the mounting studs on the reflector with the mounting slots on the fixture. 2. Insert the reflector, and turn it clockwise until it clicks into place. To remove the reflector, push and hold the Bowens-mount release, and turn the reflector counterclockwise. POWERING THE RADIANCE AC POWER Important The Radiance is a multivoltage fixture capable of running on 100–240 V, 50/60 Hz.
ADJUSTING THE BRIGHTNESS Instructions The power supply has two sets of rubber feet that allow you to stand the unit horizontally or vertically. BATTERY POWER The Radiance can be powered by two V-mount batteries. Important Both V-mount batteries must be attached to operate the Radiance on battery power. When attaching the batteries, make sure the power switch is in the off (O) position, and the fixture is not plugged into a wall outlet.
Use the same steps to set the channel and DMX address numbers. To set the channel or DMX number: 1. Touch the on-screen menu button. The first digit will blink. 2. Touch the Enter button to change the number in increments of 1. 3. Follow steps 1 and 2 to set the second and third digits. 4. After setting all three digits, press the Menu button to accept your selection. REMOTE OPERATION POWERING ON/CHARGING THE REMOTE Press the power button to turn on the remote. The LCD screen will illuminate.
Instructions SETTING THE CHANNEL ID ADJUSTING BRIGHTNESS The remote and the Radiance must be set to the same channel in order to operate the light via the remote. To adjust the brightness via the remote: To set the channel number, follow these steps: 2. Touch the brightness button on the screen. The brightness value will blink. 1. Touch the on-screen channel ID button. The first digit will blink. 2. Touch the on-screen up/down buttons to make a selection. 3.
USING DMX Note When the Radiance is connected to a DMX console, the remote is disabled. To set up DMX operation on the Radiance, follow these steps: 3. Refer to the DMX console’s user manual to set the DMX address on the controller. Set the DMX ID on the Radiance by following the instructions in Setting the Channel and DMX ID above. Instructions The Radiance supports DMX-512, so a DMX console can remotely control the the light’s settings.
PRODUCT SPECIFICATIONS Specifications LIGHT FIXTURE Expected Lamp Life: 50,000 Hr. LED Chip Type: COB Dimensions (H×W×D): Light: 11.5 × 8.5 × 14 in. (29.2 × 21.6 × 35.6 cm) Power adapter: 11.25 × 4.6 × 4.75 in. (28.6 × 11.7 × 12.1 cm) Output Power: 230 W Beam Angle: 46° without reflector 64° with reflector Color Temperature: 5600 K Color Accuracy Standard: CRI 95 TLCI 95 Cooling System: Fans on light and power adapter Dimming: Yes, 100% to 0% Display: LCD Housing Material: Metal Weight: Light: 6.
POWER Battery Plate: V-mount (×2) AC Input Power: 100 to 240 V AC, 50/60 Hz Power Input Connector: 9 pin DC Input Power: 24 V, 15 A DC DMX Connector: RJ45 Power Source: AC Adapter, 9-Pin XLR, V-mount battery Service Connector: No MOUNTING Fixture Mount: 5/8 in. receiver REMOTE OPERATION Remote Control Type: 2.
ONE-YEAR LIMITED WARRANTY This Genaray product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
