User's Manual

ManualsBrandsGemtek Technology ManualsComputers & AccessoriesWireless Access Point

WRTR-262GN User Manual

Chapter 1 Product Overview

Features

Supports IEEE802.11n and IEEE802.11b/g

With support for Wireless-N, Wireless-G, and Wireless-B standards, WRTR-262GN can transfer data to

and from all standard 2.4 GHz wireless clients.

Dual speed mode

Dual speed mode makes wireless transmission faster by using 2 channels, allowing 150Mbps data

transmission.

Support WPS

Both WPS (Wi-Fi Protected Setup) is supported.

Security Features

WRTR-262GN is equipped with following security features:

• WPS

• WPA-PSK (TKIP/AES)

• WPA2-PSK(TKIP/AES)

• WPA/WPA2 mixed PSK

• WEP(128/64bit)

• Privacy Separator

• MAC address access restriction

• Deny Any Connection/SSID stealth feature

• Web configuration screen with password

• Firewall feature with easy rules

Automatic Channel Selection

Monitors wireless interference and automatically assigns the clearest, best channel.

Summary of content (13 pages)

PAGE 1
WRTR-262GN User Manual Chapter 1 Product Overview Features Supports IEEE802.11n and IEEE802.11b/g With support for Wireless-N, Wireless-G, and Wireless-B standards, WRTR-262GN can transfer data to and from all standard 2.4 GHz wireless clients. Dual speed mode Dual speed mode makes wireless transmission faster by using 2 channels, allowing 150Mbps data transmission. Support WPS Both WPS (Wi-Fi Protected Setup) is supported.
PAGE 2
Initialization To restore settings back to the factory defaults, hold down the Reset button on the side of the unit. Browser Based Administration This unit can be easily configured from a web browser on your computer. 150 Mbps High Speed Mode 150 Mbps is the link speed of WRTR-262GNwhen using Wireless-N mode. It represents actual wireless data speeds, including overhead. Because the overhead is not available for user data transfer, usable wireless throughput will be substantially slower.
PAGE 3
DIAG LED (Red) This indicates the status of the unit depending on the number of blinks per cycle. Note: When the unit is first turned on or restarted, the Diag LED will blink for almost a minute during boot. This is normal. Internet LAN 1-4 LED (Green) On: functionality is enabled Off: functionality is disabled WIRELESS LED (Green) Indicates wireless LAN status. Blinking: Wireless LAN is transmitting On: Wireless LAN is connected but not active SECURITY LED (Amber) Indicates security status.
PAGE 4
WPS Botton Hold down this button until the Security LED flashes (about 1 second), while the unit’s power is on, initiates WPS mode, allowing the unit to exchange security keys with WPS compatible devices. LAN Port 1~4 Connect your computer, hub, or other Ethernet devices to these ports. This switching hub supports 10Mbps and 100Mbps connections. INTERNET Port 10Mbps and 100Mbps connections are supported.
PAGE 5
RESET Button Holding this button until the Diag LED comes on, while the unit's power is on, will initialize its settings. Chapter 2 Installation Manual Setup To configure your WRTR-262GN manually, follow the procedure below. 1.
PAGE 6
2. Unplug the LAN cable which connects your computer and modem. modem turn off the computer disconnect 3. disconnect Plug one end of the LAN cable into your modem and the other side to the Internet port of WRTR-262GN. Turn on your modem. modem connect connect Internet port WRTR-262GN 4. Connect your computer to one of WRTR-262GB’s LAN ports with the Ethernet cable. Turn on WRTR-262GN, wait one minute, and then turn on your computer.
PAGE 7
6. Wait for a while, and then make sure that the WRTR-262GN’s LEDs are lit: 7. Launch a web browser. If the “home” setup screen is displayed, setup is complete. If a user name and password screen are displayed, enter "user " (in lower case) for the user name, the password is the same. Click “ OK”. Follow the instructions on the screen to complete setup. You’ve completed initial setup of WRTR-262GN.
PAGE 8
Chapter 3 Configuration This chapter explains the advanced settings for WRTR-262GN. To change advanced settings, use the WRTR-262GN’s web-based configuration utility. How to Access the Web-Based Configuration Utility To display the configuration of the AirStation, follow the procedure below. 1 2 Launch a web browser. Enter the router’s LAN-side IP address in the address field, and press the "Enter" key. Note: ･ WRTR-262GN’s default LAN-side IP address depends on its mode setting. In router mode: 192.
PAGE 9
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 10
this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device has been designed to operate with an antenna having a maximum gain of 5 dBi.
PAGE 11
European Union Notice: This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
PAGE 12
NCC statement: (For Taiwan) 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
PAGE 13
Invironmental Information • The equipment that you have purchased has required the extraction and use of natural resources for its production. • The equipment may contain hazardous substances that could impact health and the environment. • In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems.