LTE Cat 6 Single-Mode Indoor CPE WLTFSM-136ACN_384041 Quick installation Guide 1
LED Indicators LED Indication 1 Power Status Description ON Power ON OFF Power OFF ON Wi-Fi ON OFF Wi-Fi OFF Flashing Transmitting data ON VoIP ON OFF VoIP OFF 2 WiFi status 3 VoIP Status 2
Display signal strength 1 LED: 5dB < CINR < 10dB ON 4 5 2 LED: 10dB < CINR < 18dB Signal Strength 3 LED: 18dB < SINR OFF SINR < 5dB Flashing Scanning Base Station Firmware All LED Upgrade Flashing 3
Connectors Connector Description Power (DC-12V Port) The power port is where you connect the enclosed power adapter. Power On/Off Switch The on/off switch support to turn off device 2 WPS Holds down the button for 5 seconds to WPS enable 3 Reset Holds down the button for 5-seconds to factory defaults. 4 LAN – RJ -45 The LAN port allows you to connect Modem to your PC or Hub using a Cat.
network cable. 5 USB Type A Host Support USB 2.0 Host 6 Voice– RJ-11 The voice port allows you to connect your Phone to this Modem 7 Antenna Connector Support external Antenna with SMA Connectors 8 USIM Slot Support 2FF size ; 1.8V/3.
Please follow the steps below to install the device: Step1: Connect the device LAN port to your PC with a RJ-45 Ethernet cable that is supplied. Step2: Insert SIM card into the device with right direction. Step3: Insert the power cord into the LTE Indoor CPE's DC-12V power jack; and insert the plug into power outlet. Step4: Switch ON the power. The device will start the booting process. After a few seconds, the LED lights will start blinking.
Please follow the steps below to configure your device through the web interface: Step1: Open the Web browser (Internet Explorer) and enter the default IP address of the IDU CPE : http://192.168.15.1 Step2: Enter username/password to access the web management interface. http://192.168.15.1 Username : administrator Password : administrator The page displays in your browser after login; you can simply configure the device settings.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Industry Canada statement: This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
Caution: the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; Avertissement: les dispositifs fonctionnant dans la bande de 5150 à 5250MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; Radiation Exposure Statement: This equipment complies with Canada radiation exposure
Europe – EU Declaration of Conformity This device complies with the essential requirements of the Radio Equipment directive: 2014 / 53 / EU. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the Radio Equipment directive: 2014 / 53 / EU: EN 300 328 V2.1.1 EN 62311:2008 EN 50385:2002 Draft EN 301 893 V2.1.0 EN 301 908-1 V11.1.1 EN 301 908-13 V11.1.1 Draft EN 301489-1 V2.2.0 Draft EN 301489-17 V3.2.0 Draft EN 301 489-52 V.1.1.
PT RO SI SK FI SE UK LI IS NO TR CH 12
