User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
Wizards
Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote
Access
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 63
2
Configuring the Cisco IPSec VPN User Groups
In the Cisco IPSec VPN - User Group Setting window, follow these procedures to
create a Cisco IPSec VPN user group.
STEP 1 Click Add to add a Cisco IPSec VPN user group.
Other options: To edit an entry, click Edit. To delete an entry, click Delete. To
delete multiple entries, check the boxes of multiple entries and click Delete
Selection.
After you click Add, the New Group - Add/Edit window opens.
STEP 2 In the Group Settings tab, enter the following information:
• Name: Enter an unique name that contains the letters, numbers, or underline
for the Cisco IPSec VPN user group.
• Services: Specify the service policy for the group. The Cisco IPSec VPN
service must be enabled for this user group so that all members of the group
to securely access your network resources over the IPSec VPN tunnels.
STEP 3 In the Membership tab, specify the members of the user group.
• To add a member, select an existing user from the User list and then click the
right arrow ->. The members of the groups appear in the Membership list.
• To delete a member from the group, select the member from the
Membership list and then click the left arrow <-.
• To create a new user, enter the user name in the User Name field and the
password in the Password field, enter the password again in the Password
Confirm field, and click Create.
STEP 4 Click OK to save your settings.
Using SSL VPN to Establish the SSL VPN Tunnels
Use the Remote Access Wizard to set your security appliance as a SSL VPN
gateway to establish the SSL VPN tunnels and allow remote users to securely
access the corporate network resources.
STEP 1 Click Wizards -> Remote Access.
The Getting Started window opens.