User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
Wizards
Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 40
2
• Wireless Channel: Choose a channel or choose Auto to let the system
determine the best channel to use based on the environmental noise levels
for the available channels.
STEP 11 After you are finished, click Next.
The Wireless Connectivity Type - Intranet WLAN Access window opens. From this
page you can configure the wireless connectivity settings for the SSID1.
NOTE The ISA550W and ISA570W support four SSIDs. To configure the wireless
connectivity settings for other SSIDs, go to the Wireless -> Basic Settings
page or use the Wireless wizard. For more information, see Configuring the
Access Points, page 151 or Using the Wireless Wizard to Configure the
Wireless Settings for ISA550W and ISA570W, page 40.
• SSID Name: The SSID name.
• Security Mode: Choose the encryption algorithm for data encryption for this
SSID. Depending on the selected security mode, configure the
corresponding settings. See Configuring the Security Mode, page 162.
• VLAN Name: Choose the VLAN to which this SSID is mapped. All traffic from
the wireless clients that are connected to this SSID will be directed to the
selected VLAN.
STEP 12 After you are finished, click Next.
The Summary window opens. The Summary page displays the summary
information for all configurations you made.
STEP 13 Click Submit to save the settings.
Using the Wireless Wizard to Configure the Wireless Settings
for ISA550W and ISA570W
Use the Wireless Wizard to configure the wireless radio and Intranet connectivity
settings for the ISA550W and ISA570W. It includes the following sections:
• Using the Wireless Wizard to Configure the Wireless Settings, page 41