User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
User Management
Configuring the User Authentication Settings
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 278
9
The local database on the security appliance can support up to 100 users and 16
groups. If you have more than 100 users, you need to use the AAA server for
authentication.
This section includes the following topics:
• Authentication Methods for User Login, page 278
• Using Local Database for Authentication, page 279
• Using RADIUS Server for Authentication, page 279
• Using Local Database and RADIUS Server for Authentication, page 282
• Using LDAP for Authentication, page 283
• Using Local Database and LDAP for Authentication, page 286
• Configuring the User Session Settings, page 286
Authentication Methods for User Login
The security appliance supports the following authentication methods for user
login.
• Local Database: Allows you to use the local database for authentication if
the number of users is relatively small. Only the local users in local database
are allowed to access the network resources. See Using Local Database
for Authentication, page 279.
• RADIUS: Allows you to use the RADIUS server for authentication if you
have more than 100 users. See Using RADIUS Server for Authentication,
page 279.
• RADIUS + Local Database: Allows you to use both the RADIUS server and
local database for authentication. See Using Local Database and RADIUS
Server for Authentication, page 282.
• LDAP: Allows you to use the LDAP for authentication if you use an AAA
server such as LDAP and AD to maintain the user and user group
information. See Using LDAP for Authentication, page 283.
• LDAP + Local Database: Allows you to use both the LDAP and local
database for authentication. See Using Local Database and LDAP for
Authentication, page 286.