User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
VPN
Configuring the SSL VPN
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 260
8
Installing the Cisco AnyConnect VPN Client on User’s PC
You can set up a user’s PC to run the Cisco AnyConnect VPN Client in standalone
mode by installing the client software for the appropriate operating system
directly on the user’s PC. In standalone mode, the user starts the Cisco
AnyConnect VPN Client, and needs to provide the authentication credentials.
The security appliance supports the Cisco AnyConnect VPN Client v2.x and v3.0
(SSL VPN function only). The Cisco AnyConnect VPN Client is compatible with the
following platforms:
• Windows 7 32-bit (x86) and 64-bit (x64)
• Windows Vista 32-bit (x86) and 64-bit (x64), including Service Packs 1 and
2 (SP1/SP2)
• Windows XP SP2+ 32-bit (x86) and 64-bit (x64)
• Mac OS X 10.5 and 10.6.x
• Linux Intel (2.6.x kernel)
You can find the software installer on the CD. If you have a CCO account, you can
access the SSL VPN portal to download the software installer from Cisco.com
website. For more information about the SSL VPN portal, see Configuring the SSL
VPN Portal, page 266.
Importing the Certificates for User Authentication
The SSL VPN gateway holds a CA certificate that is presented to the client when
the client first connects to the gateway. The purpose of this certificate is to
authenticate the server. For complete details about importing the certificates, see
Managing the Certificates for Authentication, page 310.
Configuring the SSL VPN Users
The ISA550 and ISA550W supports 25 SSL VPN users. The ISA570 and ISA570W
supports 50 SSL VPN users.
To configure the SSL VPN users and user groups, go to the Users -> Users &
Groups page. You can add all SSL VPN users to one group (such as “ SSL VPN
User Group”). However, if you have multiple SSL VPN group policies for different
SSL VPN users, you must create multiple user groups and specify different SSL