User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
Wireless Configuration for ISA550W and ISA570W
Configuring the Access Points
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 168
5
NOTE You can also change the settings in the above fields.The RADIUS
server settings you specify will replace the default settings of the
selected group. Go to the Device Management -> RADIUS Settings
page to maintain the RADIUS server settings. See Configuring the
RADIUS Servers, page 319.
STEP 10 If you choose WPA2-Enterprise as the security mode, enter the following
information:
• Encryption: WPA2-Enterprise always uses AES encryption algorithm for
data encryption.
• Key Renewal Timeout: Enter a value to set the interval at which the key is
refreshed for clients associated to this AP. The valid range is 0 to 86400
seconds. A value of 0 indicates that the key is not refreshed. The default is
3600 seconds.
• RADIUS Server ID: Choose an existing RADIUS group for client
authentication. The RADIUS server settings of the selected group are
displayed. You can also change the RADIUS server settings.The RADIUS
server settings you specify will replace the default settings of the selected
group. Go to the Device Management -> RADIUS Settings page to
maintain the RADIUS server settings. See Configuring the RADIUS
Servers, page 319.
STEP 11 If you choose WPA/WPA2-Enterprise Mixed as the security mode, enter the
following information:
• Encryption: WPA/WPA2-Enterprise Mixed automatically choose TKIP or
AES encryption algorithm for data encryption.
• Key Renewal Timeout: Enter a value to set the interval at which the key is
refreshed for clients associated to this AP. The valid range is 0 to 86400
seconds. A value of 0 indicates that the key is not refreshed. The default is
3600 seconds.
• RADIUS Server ID: Choose an existing RADIUS group for client
authentication. The RADIUS server settings of the selected group are
displayed. You can also change the RADIUS server settings.The RADIUS
server settings you specify will replace the default settings of the selected
group. Go to the Device Management -> RADIUS Settings page to
maintain the RADIUS server settings. See Configuring the RADIUS
Servers, page 319.