User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
Networking
Configuring the WAN Redundancy
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 117
4
STEP 4 To check the connection of both links at regular intervals after you enable the
Failover mode, you first need to enable the Link Failover Detection feature. To
configure the Link Failover Detection settings, go to the Networking -> Link
Failover Detection Settings page. See Configuring the Link Failover Detection,
page 117.
Routing Table for WAN Redundancy
The Routing Table feature allows the traffic to meet the static routing policies you
defined on your security appliance to pass through different WAN interfaces.
You need to add default routing policies that forward the traffic to the primary
WAN. The traffic for other static routings are forwarded to the secondary WAN. For
more inforamtion to configure the static routing policies, see Configuring the
Static Routing, page 132.
NOTE The Link Failover Detection settings will be ignored if you enable the Routing Table
feature.
Configuring the Link Failover Detection
The Link Failover Detection feature detects the link failure. If a failure occurs, traffic
for the unavailable link is diverted to the active link.
NOTE The Link Failover Detection settings are only available when the WAN redundancy
is set to Load Balancing or Failover.
STEP 1 Click Networking -> WAN Redundancy -> Link Failover Detection Settings.
The Link Failover Detection Settings window opens.
STEP 2 Enter the following information:
• Failover Detection: Click On to enable the Link Failover Detection feature, or
click Off to disable it.