User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
Status
VPN Status
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 83
3
SSL VPN Status
The SSL VPN Monitoring page displays the status and traffic statistic information
of all SSL VPN sessions. To open this page, click Status -> VPN Status ->
SSLVPN Monitoring.
Status of all Active SSL VPN Sessions
The Sessions tab displays the following information of all active SSL VPN
sessions:
Remote
Gateway
The IP address of the remote gateway for a Site-to-Site
VPN session or the IP address of the remote VPN client for
a Cisco IPSec VPN session.
Tx Bytes The volume of traffic in Kilobytes transmitted from the VPN
tunnel.
Rx Bytes The volume of traffic in Kilobytes received from the VPN
tunnel.
Tx Pkts The number of IP packets transmitted from the VPN tunnel.
Rx Pkts The number of IP packets received from the VPN tunnel.
Session ID The SSL VPN session ID.
User Name The name of the connected SSL VPN user.
Client IP (Actual) The actual IP address used by the SSL VPN client.
Client IP (VPN) The virtual IP address assigned by the SSL VPN gateway.
Time Connected The amount of time since the user first established the
connection.
Disconnect Click this button to terminate an active SSL VPN session
and hence the associated SSL VPN tunnel.
Disconnect All Click this button to terminate all active SSL VPN sessions
and hence the associated SSL VPN tunnels.