User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
Status
Interface Status
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 76
3
WAN Table
The WAN table displays the following information of all WAN interfaces:
VLAN Table
The VLAN table displays the following VLAN information:
PVID The Port VLAN ID (PVID) to be used to forward or filter the
untagged packets coming into the port. The PVID of a Trunk
port is fixed to the DEFAULT VLAN (1).
Speed/Duplex The duplex mode (speed and duplex setting) of the
physical port.
Link Status Shows if the physical port is connected or not.
Name The name of the WAN interface.
WAN Type The network addressing mode used to connect to the
Internet for the WAN interface.
Connection Time How long the WAN interface is connected, in seconds.
Connection
Status
Shows if the WAN interface obtains an IP address
successfully or not. If yes, the connection status shows as
“Connected”.
MAC Address The MAC address of the WAN interface.
IP Address The IP address of the WAN interface that is accessible from
the Internet.
Netmask The IP address of subnet mask for the WAN interface.
Gateway The IP address of default gateway for the WAN interface.
DNS Server The IP address of the DNS server for the WAN interface.
Physical Port The physical interface that is associated with the WAN
interface.
Link Status Shows if the cable is inserted to the WAN interface or not. If
the link status shows as “Not Link”, the cable may be loose
or malfunctioning.
Zone The zone to which the WAN interface is assigned.