User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
Wireless Configuration for ISA550W and ISA570W
Configuring the Access Points
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 167
5
• Shared Secret: The Pre-shared Key (PSK ) is the shared secret key for WPA.
Enter a string of at least 8 characters to a maximum of 63 characters.
• Key Renewal Timeout: Enter a value to set the interval at which the key is
refreshed for clients associated to this SSID. The valid range is 0 to 86400
seconds. A value of 0 indicates that the key is not refreshed. The default is
3600 seconds.
STEP 9 If you choose WPA-Enterprise as the security mode, enter the following
information:
• Encryption: Choose either TKIP or AES as the encryption algorithm for data
encryption. The default is TKIP.
• Key Renewal Timeout: Enter a value to set the interval at which the key is
refreshed for clients associated to this AP. The valid range is 0 to 86400
seconds. A value of 0 indicates that the key is not refreshed. The default is
3600 seconds.
• RADIUS Server ID: The security appliance predefines three RADIUS
groups, choose an existing RADIUS group for client authentication. The
following RADIUS server settings of the selected group are displayed.
- Primary RADIUS Server IP Address: The IP address for the primary
RADIUS server.
- Primary RADIUS Server Port: The port number for the primary RADIUS
server.
- Primary RADIUS Server Shared Secret: The shared secret key for the
primary RADIUS server.
- Secondary RADIUS Server IP Address: The IP address for the
secondary RADIUS server.
- Secondary RADIUS Server Port: The port number for the secondary
RADIUS server.
- Secondary RADIUS Server Shared Secret: The shared secret key for
the secondary RADIUS server.