User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
Networking
Configuring the Quality of Service
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 151
4
Configuring the Wireless QoS Classification Methods
Traffic Classification is used to classify the traffic through the SSIDs to a given
traffic class so that traffic in need of management can be identified. Use the
Classification Method page to specify the classification method that is used by
each SSID individually.
STEP 1 Click Networking -> QoS -> Wireless QoS -> Classification Method.
The Wireless Classification Method window opens.
STEP 2 Depending on your networking design, choose either DSCP or CoS remarking
method for traffic through each active SSID.
STEP 3 Click Save to apply your settings.
Mapping CoS to Wireless Queue
STEP 1 Click Networking -> QoS -> Wireless QoS -> Mapping CoS to Queue.
The Mapping CoS to Queue window opens.
STEP 2 Choose the traffic forwarding queue to which the CoS priority tag value is
mapped.
STEP 3 Click Save to apply your settings.
Mapping DSCP to Wireless Queue
STEP 1 Click Networking -> QoS -> Wireless QoS -> Mapping DSCP to Queue.
The Mapping DSCP to Queue window opens.
4 100xxx Q2 (Video Priority) 4
5 101xxx Q2 (Video Priority) 5
6 110xxx Q1 (Voice Priority) 6
7 111xxx Q1 (Voice Priority) 7
802.1p DSCP Wireless Queue WMM value