User's Manual

Operation
1. Plug the power adapter into the wall socket.
2. USB-A side connects to the power wall adapter, USB-C
side connects to the wireless charger side, the LED light will
illuminate blue which means the unit is ready to charge your
device.
3. Place your device on to the charging stand, the blue LED
light will be pulsing which denotes the device is being charged.
Specification
Input: 9V/3.0A
Output: 10W*2 (Max)
Transmission Distance: ≤5mm
Efficiency: ≥75%
Product size: L240*W101*H258mm
Packing
• Truman Dual Wireless Charger and Headphone Stand
• USB–A to USB–C type charging cable
• User Manual
Overview
Note: Only the QC2.0/QC3.0 Standard power adapter can support
this product's fast charging. Adapters are not included with the
product.
Truman Dual Wireless Charger and
Headphone Stand
Instruction Manual
IC: 21530-100937
FCC ID: 2AGR4-100937
FCC Statement
This device complies with part 15 and part 18 of the FCC Rules.
Operation is Subject To the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference
that may cause undesired operation. Changes or modifications not
explicitly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
Note: this equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 and part 18 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and candidate radio frequency
energy and, if not installed and used in accordanc
e with the
instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. During the operation of
device
a distance of 15 cm surrounding the device and 20 cm
above the top surface of the device must be respected.
This device complies with Part 18 of the FCC Rules. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Indicating status and protection function
ISED Statement
This device complies with Industry Canada’s license-exempt RSSs.
Operation is subject to the following two conditions:
● This device may not cause interference; and
● This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
● l’appareil ne doit pas produire de brouillage;
● l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
This equipment complies with Canada radiation exposure limits set
forth for an uncontrolled environment.
During the operation of device a distance of 10 cm surrounding the
device and 10 cm above the top s
urface of the device must be
respected.
Cet équipement est conforme Canada limites d'exposition aux
radiations dans un environnement non contrôlé.
au cours de l'opération de l'appareil sur une distance de 10 cm
autour de l'appareil et de 10 cm
au - dessus de la surface supérieure de l'appareil doit être respecté.
● Increase the separation between the equipment and any other radio
device.
● Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
1. LED blue light: Standby
2. LED blue pulsing light: Charging
3. Blue light flashing: Device is not correctly placed on the
wireless charger, over temperature protection, or detects
metal on the back of the device.
Indicator Light
Wireless charger
Wireless charger
USB Micro Cable
USB-C Interface
Power Adapter
page 03
Back Cover
page 04
page 02Front Cover
page 05
page 06
page 07
page 08
page 09
page 10
instruction sheets
1) The folded size should be 3”W x 3”H.
2) Please exactly follow all the trim marks and fold marks.
3) Please exactly follow the page in proper order.(The page numbers do not need to print.)
4) Use 128gsm gloss art paper for bulk production.
5) The color of this kind instruction is : 1C(C0M0Y0K100)
6) “S” fold should be used for this item.
Charging frequency: 110.7-148 KHz