User's Manual

Front Cover page 02 page 03
page 06 page 07 page 08
BLUETOOTH
®
OPERATION
page 09
page 04
Back Cover
SPECIFICATION
Model: 100200-001B
Bluetooth Specification: Bluetooth® V4.2
Profiles Supported: AVRCP.TS.1.6.0/A2DP.TS.1.3.1/HFP.TS.
1.7.0/RF.TS.4.2.0/BB.TS.4.2.0
Wireless Working Range: 10m (without obstacles)
Built-in Battery: 3.7V/300mAh
USB Recharge Voltage: DC 5V
Output Power: 15mW
Frequency Response: 20Hz-20KHz
OVERVIEW
1. LED light key(M)
2. Multi-function button (MFB)
3. Volume+
4. Volume-
5. Microphone
6. TF card slot
7. LED light
8. 3.5mm audio port
9. USB Charging Port
PACKING LIST
Halo Lighted Bluetooth® Headphone
USB Charging Cable
3.5mm AUX Cable
Storage Pouch
User Manual
Gift Box
Instruction Manual
FCC ID: 2AGR4-100200
IC ID: 21530-100200
1. Please ensure that the Bluetooth function has been turned on in the
settings of your Bluetooth enabled device.
2. Turn the headphone on by holding down the MFB for about 2 seconds.
The LED indicator light will flash to detect Bluetooth enabled devices near
you and will enter pairing mode.
3. ”GEMLINE HP” will appear on the Bluetooth device list, select
“GEMLINE HP” to establish pairing. If instructed to enter a PIN code,
please enter ‘0000’.
4. The LED indicator light will turn blue to indicate successful pairing.
5. When you want to play audio from another Bluetooth device, disconnect
the headphone from the original device and follow steps 1-3 to re-pair the
headphones with a new Bluetooth enabled device.
BUTTON CONTROL
●Power On/Off: long press the MFB button
●Play/Pause: Short press the MFB button
●PREV: Long press - to select the previous song
●NEXT: Long press + to select the next song
●Volume Up: Short press + button to increase volume
●Volume Down: Short press - button to decrease volume
HANDS-FREE PHONE USE
●Answer incoming call: Short press MFB button
●End call: Short press MFB button once
●Redial last call: Dual press MFB button
●Reject incoming call: Press MFB button for 2 seconds
page 05
SD CARD PLAYING
Insert a SD card, the headphone will play the music on the card
automatically.
Short press Mode switch can be changed to Bluetooth mode.
AUX PLAYBACK OPERATION
1.Turn on the headphone.
2.Connect the headphone to a smartphone, audio device, or laptop with
the 3.5mm AUX cable(included)
3.The next/previous song, volume, and play/pause buttons can only be
adjusted on the device that is connected through the 3.5mm AUX cable.
CHARGING THE HEADPHONE
1.When the battery is low, please charge via the included USB cable. The
charging time is approximately 2 hours and provides up to 5.5 hours of
continuous operation. Standby time is approximately 12 hours.
2.The LED indicator light will be red during charging and the blue light will
be bright once it is fully charged.
WARNING
1. Do not disassemble, repair, or modify the headphone.
2. Do not place product in or near fire to avoid danger, as it uses a lithium
battery.
3. Avoid storage at extreme temperatures, this can shorten the battery life
and may affect the headphone.
The Bluetooth® word mark and logos are registered trademarks owned by
the Bluetooth SIG, Inc. and any use of such marks by The Gem Group is
under license. Other trademarks and trade names are those of their
respective owners.
instructions,
may cause harmful interference to radio communications. However, there
is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which
can be determined by turning the equipment off and on, the user is
encouraged to
try to correct the interference by one or more of the following measures:
NOTE: This equipment has been tested and found to comply with the
limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are
designed to provide reasonable protection against harmful interference in
a
residential installation. This equipment generates uses and can radiate
radio
frequency energy and, if not installed and used in accordance with the
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible
for compliance
could void the user's authority to operate the equipment. This device
complies with Part
15 of the FCC Rules. Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including
interference that may
cause undesired operation.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two
conditions:(1) This device may not cause interference.(2) This device must
accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil
est conforme aux CNR d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) L' appareil ne doit pas produire de brouillage;
(2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d' en compromettre le fonctionnement.
Problem Troubleshooting Method
KIND REMINDER
4. Keep the headphone dry and do not store the headphone in damp
areas to avoid damage to the headphone.
5. Avoid dropping the headphone as it may cause damage the product.
1. To prolong the headphone life span and to avoid hearing damage,
please do not listen to music under high volume for long periods of time.
2. When an error occurs with the headphone, please turn off the
headphone and restart it to troubleshoot.
3. When the headphone power is low, the Bluetooth range may be
affected. Please charge the headphone to avoid disruptions during use.
Unable to pair the
headphone with a
mobile device
1. Inspect whether the headphones are searching for a
Bluetooth enabled device to connect to. If not, restart
the headphone.
2. Difficulty in searching and connecting to a desired
device can be affected if multiple devices are equipped,
turned on, and in range for Bluetooth connectivity.
Please turn off or disable the Bluetooth function on the
other devices.
3. The power of the battery is insufficient, please
recharge the headphone.
Problem Troubleshooting Method
The music stops from
time to time
1. Inspect the distance between the headphone and the
Bluetooth enabled device, it may exceed the Bluetooth
transmission range.
2. Inspect if there is an obstacle between the
headphone and the Bluetooth enabled device.
3. The power of the battery is insufficient, please
recharge the headphone.
The sound is low or
distorted
1. Inspect the volume of the connected headphone or
Bluetooth enabled device and adjust the volume as
needed.
2. The power of the battery is insufficient, please
recharge the headphone.
The Bluetooth indicator
light remains OFF
1. The power of the battery is insufficient, please
recharge the headphone.
2. Restart the headphone.
Halo Lighted Bluetooth® Headphones