User Manual TE-304B-A12 GEM-OX-GU
Product manuals Packing list Product model listing subsidiary note TE-304B-A12 1 PCS GPS device American version 1 copy of user manual TE-304B-E12 1 PCS GPS device European version 1 copy of user manual Introduction GPS device connects to car battery. Do not jump over the fuse to connect to car battery directly(see figure). Note: THE ACC must be connected, otherwise the device will go to sleep.
SIM card Introduction Guide Open the back card cover, insert the SIM card into the slot, and then close the buckle.( You need to buy the card by yourself) Type of card supported: Nano SIM card. Unplug The SIM Card Open the black card cover with the disassembly tool,pull out the card slot cover by hand,remove the sim card,and then close the card cover.
Indicator light Indicator status Status FLICKER SLOWLY NETWORK SEARCHING （200MS ON/1800 MS OFF） Green GSM FLICKER SLOWLY IDLE indicator （1800 MS ON/200 MS OFF） FLICKER QUICKLY DATA TRANSFER IS ONGOING （125MS ON /125 MS OFF） ALWAYS ON VOICE CALLING FLICKER QUICKLY GPS IS NOT FIX Blue GPS （200MS ON/200 MS OFF） indicator FLICKER SLOWLY GPS FIX （1000 MS ON/4000 MS OFF ） ALWAYS OFF GPS FAULTY Signal Line Connector 12 Pin Signal Line Wire Name Remarks colour 1 B+ 9-90V DC 黄色 2 GND GND
6 12V out 7 Din3 12V output Imax = 120mA 粉黑色 0 up to 90V tolerance 蓝色 Din3 0-8V is logic '0' Din3 8-90V is logic '1' 8 RS232_TX1 橙白色 9 RS232_RX1 蓝白色 10 Dout2 11 1-wire 12 Ain1 - Open-drain with Imax = 350mA 棕色 紫色 0V to B+ (90V) 绿色 98.5% accuracy 12bit ADC. Install The Device 1.Installation Precautions （a）Do not install the device near the source of interference; （b）No metal objects above the device; 2.
Device Parameter Setting 1. Send a text message to the device through a mobile phone; The parameter setting is completed after the mobile phone receives a feedback SMS from the device. 2.
1.If the wireless signal is low, the setting may fail.please check GSM LED indicator. 2.please check the sent SMS content according to device feedback SMS. 3.Please try to reset the device by pressing the Reset button,and set the parameter again.
gsensorcrashsens conf set gsensorcrashsens val(val range 0-10) protocoltype conf set protocoltype val(0-wialon,2GEM) ipaddr conf set ipaddr *** port conf set port *** Other SMS Commands 1.update app: device firmware upgrade 2.reset: restart the device 3.factory: restore factory settings （Please contact Thinkpower for more SMS commands.） Precautions 1. The main body of the product contains batteries, please do not approach the fire source or cast it Into the water to avoid the risk of fire. 2.
Weight: 160g（Contains the tail line） Waterproof Grade: IP67 Operating Temperature: -20~60℃ FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
—Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.
