Over RGB EXT-HDMI-5BNC User Manual www.gefen.
ASKING FOR ASSISTANCE Technical Support: Telephone Fax (818) 772-9100 (800) 545-6900 (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday. Write To: Gefen Inc. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen Inc. reserves the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice. HDMI Over RGB is a trademark of Gefen Inc. © 2008 Gefen Inc.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender Panel Layout 5 Sender Panel Descriptions 6 Receiver Panel Layout 7 Receiver Panel Descriptions 8 Connecting And Operating The HDMI Over RGB 9 Specifications 10 Warranty
INTRODUCTION Congratulations on your purchase of the HDMI Over RGB. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE HDMI OVER RGB • The HDMI Over RGB is designed for either 4 or 5 BNC cable type setups. When 5 BNC cables are present and used, a power supply on the HDMI Over RGB Receiver will not need to be used. Power will be transmitted over the cables. When a 4 BNC cable setup is used, a second power supply (part# EXT-PS52AU) for the receiving unit will need to be purchased and connected. • HDMI 1.3 compliant.
FEATURES Features • Connects HDMI sources to remote HDMI displays over legacy RGBHV cabling • Supports extension distances of up to 330 feet • Supports resolutions up to 1080p, 2K, and 1920 x 1200 • HDMI and HDCP compliant • Extends any IR device HDMI 1.
SENDER PANEL LAYOUT Front Panel 1 2 3 4 Back Panel 5 6 7 4 8 9
SENDER PANEL DESCRIPTIONS 1 Locking 5V DC Power Supply Input Connect the included 5V DC power supply to this input port. 2 HDMI Input Port Connect the HDMI source device to this input port. A secure connection to this HDMI port can be made using Gefen Mono•LOK cables. 3 IR Out Port An IR emitter/blaster (sold separately, part# EXT-2IREMIT) must be connected to this port to use the IR Repeater feature.
RECEIVER PANEL LAYOUT Front Panel 1 2 3 4 5 Back Panel 6 7 8 6 9 10
RECEIVER PANEL DESCRIPTIONS 1 Locking 5V DC Power Supply Input When using a 5 BNC cable system this connector will not need to be used. When using a 4 BNC cable system a second 5V DC power supply (part# EXTPS52AU) must be purchased and connected to this input port. 2 IR Receiver This receiver is used for the IR Repeater feature. This receiver will accept standard IR remote commands for transmission back to the sending unit and then to the connected IR emitter/blaster.
CONNECTING AND OPERATING THE HDMI OVER RGB How to Connect the HDMI Over RGB 1. Connect the HDMI source device to the HDMI Over RGB sender unit using the supplied HDMI cable. 2. The HDMI Over RGB sender and receiver can be used with either a user supplied 4 or 5 BNC cable system. 5 BNC Cables Connect all 5 BNC cables to the R, G, B, C, and RP BNC connectors between the HDMI Over RGB sender and receiver units.
SPECIFICATIONS Video Amplifier Bandwidth ....................................................................... 340 MHz DisplayPort v1.0 compatible ............................................................................. Yes Video Resolutions (max) .................................................... 2K, 1080P, 1920x1200 Power Consumption ....................................................................... 10 Watts (max) Coaxial Connectors ...........................................................
