2x1 DVI KVM SL Switcher USER MANUAL www.gefen.
ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday. Write To: Gefen Inc. c/o Customer Service 20600 Nordhoff Street Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen Inc. reserves the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice. 2x1 DVI SL Switcher is a trademark of Gefen Inc. © 2007 Gefen Inc.
TABLE OF CONTENTS 1 Introduction 2 Features 3 Panel Descriptions 4 Connecting and Operating the SL Switcher 5 Operation Notes 6 RMT2-IR Installation 7 IR Code Conflicts / IR Extender Installation 8 Specifications 9 Warranty
INTRODUCTION Congratulations on your purchase of the Gefen 2x1 DVI SL Switcher. Your complete satisfaction is very important to us. Gefen’s line of KVM (Keyboard Video & Mouse), DVI, USB, switches, extenders, converters and hubs is designed to make computer use more comfortable, more productive and less expensive. KVM switches allow access to multiple computers from a single keyboard, while the extenders give the user control over a computer up to 330 feet away from the work area.
FEATURES Features • Saves money on hardware costs • Saves space on your desktop • Save time and increase your productivity • Maintains highest 1920 x 1200 x 60Hz resolution video • No loss of quality • Use either PC or Mac with USB keyboard/mouse • Switches easily between any two single link DVI computers • Switch between two single link DVI, USB 2.
PANEL DESCRIPTIONS Power Indicator Infrared Eye Selector Indicates which input is selected Audio In 1 5VDC Input DVI In 1 Contact Closure Interface - Connects to optional wired Audio Out RMT-2 remote control Audio In 2 DVI Out DVI In 2 USB In 1 USB Output 3 USB In 2
CONNECTING AND OPERATING THE 2x1 DVI SL SWITCHER How to Connect the SL Switcher to your devices 1- Connect the supplied cables from your first computer into the DVI In 1, USB In 1, and Audio In 1 connection in the back of the DVI Switcher. 2- Connect the supplied cables from your second computer into the DVI In 2, USB In 2, and Audio In 2 connection in the back of the DVI Switcher. 3- Connect the monitor to the DVI Out connection. 4- Connect your USB devices (e.g. keyboard, mouse) into the USB Out.
2x1 DVI SL OPERATION NOTES Operation Notes When turning on or rebooting your computers, the DVI SL Switcher must be selected to the computer that is booting until the computer completes the boot cycle. This step can be eliminated using the Gefen DVI Detective, which stores the displays EDID. If you loose your picture when switch from source 1 to source 2 or vice-versa you will need a DVI Detective.
RMT2-IR INSTALLATION 1. Remove battery cover from the back of the RMT2-IR remote. 2. Verify that dip switches 1 & 2 are in the down (OFF) position. 3. Insert the battery, hold the battery so that you can see the positive side facing up. The side that is not marked must be facing down. 4. Test the RMT2-IR remote by pressing ONLY one button at a time. The indicator light on the remote will flash once each time you press a button.
IR CODE CONFLICTS In the event of IR conflicts, please do the following: 1. Remove the battery cover from the back of the RMT 2-IR remote. 2. Locate the Dip Switches above the batteries 3. Switch the Dip Switches on the RMT 2-IR to any of the combinations pictured below. 4. Dip Switches 1 and 2 in the RMT 2-IR correspond with Dip Switches 1 and 2 on the outside of the 2x1 DVI SL Switcher respectively.
SPECIFICATIONS Video Amplifier Bandwidth ................................................................................. 165 MHz Input Video Signal ........................................................................................ 1.2 Volts p-p Input DDC Signal .................................................................................. 5 Volts p-p (TTL) Single Link Range ........................................................................................
