LH600
CONTENTS CONTENTS 1 INTRODUCTION Unpacking the LH600 2 3 DESCRIPTION 4 INSTALLATION Setting Up Wall Mounting 7 7 8 USING THE LH600 Turn the LH600 On/Off Volume Control Tone Control Telephone Use Microphone SENSE Switch Line Input Selector Microphone Input Selector 10 10 10 10 10 10 11 11 TROUBLESHOOTING 12 SAFETY INFORMATION 13 GUARANTEE 14 RECYCLING DIRECTIVES 16 1
INTRODUCTION Congratulations on purchasing your GeemarcTM LH600. This is a portable induction loop system that is suitable for the home. It is easy to setup and use and fits into any home environment with its sleek and inconspicuous design. The sound quality of the LH600 is unparalleled and will bring great pleasure during its everyday use.
INTRODUCTION Unpacking the LH600 When unpacking the LH600 you should find the following in the box: • 1 LH600 Amplifier Unit • 1 Power adaptor/charging Unit. • 1 Telephone line cord • 1 Telephone adaptor • 1 External microphone with 3m extension lead and lapel clip • 1 3.5mm stereo jack to RCA convertor • 1 2m audio cable with 3.
DESCRIPTION General Description Top View 4
DESCRIPTION Left View Mic input 2 Mic input 1 Audio input 2 Audio input 1 1V DC supply Telephone input Connections for cable loop Right View Volume Power LED Tone MIC 1 MIC 2 Line 1 Line 2 MIC sense 5
DESCRIPTION Wall Mount Hanger Wall Mount 6
INSTALLATION Setting Up Connect Amplifier to the Sound Source Place the amplifier near the sound source and connect the audio leads between the sound source and the amplifier. This direct connection method with leads gives the best results. TV Connection: For a TV with SCART connector audio output: connect the SCART adaptor to the TV set; connect the RCA jack on the SCART adaptor using the RCA convertor cable; connect the 3.5mm stereo cable to the RCA convertor cable; connect the other end of the 3.
INSTALLATION Telephone Connection: Plug the supplied telephone cord into the TEL jack . The other end of the cord should be connected to a telephone convertor adaptor. Push the plug of the telephone convertor into the telephone wall socket. Connect the Loop Wire The unit comes with a 38 meters loop wire. Place the wire on the floor following the wall edges so that the wire runs around the whole room, starting and ending at the amplifier.
INSTALLATION Connect the Microphone If for some reason a direct connection is not possible a microphone can be used to pick up the sound source. Or, a microphone can be used simultaneously with line input to pick up background noise e.g. the doorbell. A microphone can also be used for someone to speak directly into the loop system whilst the hearing aid user is listening to a sound source. Connect the external microphone wire provided into the 2.5mm stereo jack, marked MIC1 on the unit.
USING THE LH600 Turn the LH600 On/Off To turn the unit on, turn the rotary volume control clockwise. The rotary volume is located at the corner position of the unit. The power LED will turn to indicate the power is on. To turn the unit off, turn the rotary GREEN volume control fully counter-clockwise. The power LED goes off to indicate the unit power is off. Volume Control The rotary volume control adjusts the volume received by the hearing aid. Turn fully clockwise for the maximum volume.
USING THE LH600 Microphone Input Selector The microphone selection switches allow you to fick between two different microphone sources.. Select MIC1 or MIC2 depending on which source you require. Alternatively, you can use both input sources at the same time, simply press both MIC1 and MIC2.
TROUBLESHOOTING TheLH600 is producing no sound • Check all connections are secure (microphone, audio sources, loop cable, power cable) • Ensure the LH600 is turned on (check the Power LED is on) • Ensure hearing aid is switched to ‘T’ The sound produced is very quiet • Turn the audio device volume higher • Turn the LH600 volume higher • Move the microphone closer to the sound source • Check the loop cable is wired correctly The sound produced is very loud • Turn the audio device volume lower • Turn the LH60
SAFETY INFORMATION General Do not open the unit. Contact the helpline for all repairs. Cleaning Clean the LH600 with a soft cloth. Never use polish or cleaning agents - they could damage the finish or the electronics inside. Environmental Do not expose to direct sunlight. Always ensure there is a free flow of air over the surfaces of the LH600. Do not place any part of your product in water and do not use it in damp or humid conditions e.g. bathrooms.
GUARANTEE From the moment your GeemarcTM product is purchased, GeemarcTM guarantee it for the period of one year. During this time, all repairs or replacements (at our discretion) are free of charge. Should you experience a problem then contact our help line or visit our website at www.geemarc.com. The guarantee does not cover accidents, negligence or breakages to any parts. The product must not be tampered with or taken apart by anyone who is not an authorised GeemarcTM representative.
GUARANTEE Electrical connection: The apparatus is designed to operate from a 230V 50Hz supply only. (Classified as ‘hazardous voltage’ according to EN60950 standard).
RECYCLING DIRECTIVES The WEEE (Waste Electrical and Electronic Equipment) has been put in place for the products at the end of their useful life are recycled in the best way. When this product is finished with, please do not put it in your domestic waste bin. Please use one of the following disposal options: - Remove the batteries and deposit them in an appropriate WEEE skip. Deposit the product in an appropriate WEEE skip. - Or, hand the old product to the retailer.
UGLoopHear600_En_V.1.1 UK FRANCE GERMANY 5 Swallow Court Swallowfields Welwyn Garden City Hertfordshire, AL7 1SB For product support: 01707 384438 Parc de l’Etoile 2 rue Galilée BP20061 59791 GRANDE SYNTHE CEDEX TEL. SERVICE APRES VENTE: 03 28 58 75 99 Siemensstrasse 10, 53121 Bonn Germany Tel: +49(0)228/ 74 87 09 0 Fax: +49(0)228/ 74 87 09 20 www.geemarc.com www.geemarc.com www.geemarc.
