C1 (Commander) Flash Trigger Operation instruction Fit for Nikon
Catalog Safety instructions Function List Components Component instruction Preparation before use Functions description Custom function/FN Wireless channel setting Assisted focusing light Hot Shoe Nikon master control mixed mode Nikon master control Multi mode Specification List 01 02 03 06 08 10 11 12 13 14 15 17 20
Safety instructions Function List Please read this manual carefully before use. 1.Available flash mode: I-TTL, M, Multi. 2.Available for Front curtain sync/back curtain sync/ high-speed sync, highest sync speed 1/8000s. 3.Exposure compensation available. (FEC) 4.Surround expose available. (FEB) 5.Exposure Lock available. (FE LOCK) 6.Available for focusing assist lamp.(can be disabled) 7.Available for mixed flash mode, such TTL, M. 8.Available for setting auto save function. 9.
Components Rubber cap Micro USB Group B Group A/ Custom function setting 03 Components Mode Test Indicate light LCD Screen Group C Group D/Channel setting Power switch: ON/OFF Setting/restore factory setting Setting (up/down/ left/right) Battery door Twist lock Mounting holder 04
Components Component instruction LCD Screen Power Switch: Automatic focusing assist High-speed sync Manual /strobe flash mode Wireless channel Flash setting for A Flash setting for B 05 Slide to 【ON】 to power on.
Component instruction Preparation before use Hot Shoe contacts: Use it to connect with camera, compatible with Nikon. Mode: Transmitter mode option Test: Send flash signal for groups A:B:C:D Enter/exit flash setting for groups Indicate light: Power wireless communication or command indicate Battery loading Indicate light status Open the battery hatch. Install two AA batteries according to the positive and negative directions of the battery, when installation completed, close the battery hatch.
Preparation before use Install the trigger on the hot shoe contact from top of camera. Functions description Power on Load batteries correctly, push the switch to 【ON】to turn on the trigger, then LCD screen & 2 color lights are on simultaneously, system check and complete initialization, enter standby mode, red indicator flashing. Mode options Turn on the trigger, press【Mode】, now trigger enter into mode options, after turning on the transmitter,you can cycle through mix mode and the multi mode. Test 1.
Custom function/FN Wireless channel setting Press 【FN】for 2 seconds, system will change between customized settings and flash modes, enter custom mode, press 【←】/【→】to set option number. Press【D】button about 2 seconds, wireless channel light flickers and enters wireless channel setting, press 【←】/【→】to set channel from 1 to 16.
Assisted focusing light Hot Shoe If you enabled “automatic focusing”on transmitter, When the light is not enough to focus automatically, it will enable the assist focusing light in trigger to help to make focusing easier. Connecting trigger with Nikon Cameras, Press the shutter lightly, trigger will identifies the camera automatically, and send the trigger setting status to flash to I-TTL offline flash, the highest sync speed is 1/8000s.
Nikon master control mixed mode Nikon master control mixed mode Setting for groups ③ After selected a group, press【MODE】button to set the flash mode of the group,every modes parameters are as below: TTL : Compatible with i- TTL , Exposure compensation adjustment available from -3.0EV to +3.0EV, total 22 levels; press【↑】/【↓】 button to change Focal distance for different groups. M: Flash output range 1/128~1, press【←】/ 【→】to increase or decrease 0.
Nikon master control Multi mode Nikon master control Multi mode Setting for groups ② Under non-grouping setting status, press【←】/ 【→】button to set flash power, flash output is adjustable from 1/4 to 1/128, total 6 levels. ③ Under standby status, press【OK】button, you can see the Frequency numbers are flickering, press 【←】/【→】button to adjust frequency, available frequency from 1HZ-100HZ. ① Press【MODE】button to select transmitter mode as pic showed .
Nikon master control Multi mode Specification List ⑥ After you select the setting groups, press【MODE】 button to turn on/off the groups you selected, you can also press 【← 】/【→ 】to turn on/off it, press 【↑】/【↓】button to change Focal distance for different groups. System mode: Digital FSK 2.4G HZ Wireless Trigger Communication Distance: 50 meter Wireless Channel: 16 Flash mode: I-TTL, M, Multi. Synchronous mode: Front synchronize, Back synchronize, High Speed synchronize. Group control: A\B\C\D 4 groups (E
