Operation Manual

ManualsBrandsGeba Tronic ManualsVehicleTCS-Cody 3

Instructions for Assembly and Use

TCS-Cody 3

Electronic encoder-type lock

The TCS-Cody is a modern and safe alternative to traditional key switches.

The TCS-Cody can safely be used after two simple programming steps (master

code and pass code). For opening or closing of the door only a four- or five-digit

numeral code (pass code) has to be entered, which has been previously program-

med via the master code by an authorized person.

After correct input of the pass code and actuation of arrow keys UP

▲ or DOWN ▼

the drive (UP or DOWN) is triggered by the corresponding relay contact.

The high flexibility of the encoder is achieved by extensive programmability of the

individual operating functions. All sections required for operation are, however, pre-

programmed and thus immediately ready for use.

Technical Data:

24 V series 230 V series

Supply voltage 12 - 24 V AC / DC 230 V AC 50 Hz

Output 3x NO, NC relay contact, 3x NO, NC relay contact,

isolated, 8 A 250 V isolated, 8 A 250 V

Connections 2.5 mm

max., 2.5 mm

max.,

Ambient- -20 ˚C to +60 ˚C -20 ˚C to +60 ˚C

temperature

Adaptation of the TCS-Cody 3 to special requirements:

The TCS-Cody 3 is provided with a series of flexible time settings which allow the adaptation

to special cases of application. For programming these special operating modes please ask

for our flow chart for the TCS-Cody series, if required!

geba GmbH is released of its obligations regarding guarantee and product liability if - without

prior permission - the unit has been modified, or if the installation is unproper or not in

accordance with our instruction manual.

The installer has to take care that the EMC-regulations are respected.

The most important characteristics of the TCS-Cody are:

➢ Simple operation, programming and assembly.

➢ Water-protected enclosure

➢ A maximum of safety:

➢ The electronic decoder is separately installed in the

protected area

➢ Up to 50 different pass codes can be stored

Up to 100 million different coding possibilities

Variable lock-out function

Nearly unlimited data security, even with power failure

➢ Three potential-free relay outputs

After entry of a valid pass code and within 30 seconds the user can con

trol the drive unit connected in dead man‘s operation by means of arrow

keys ”UP” ▲ and ”DOWN” ▼.

➢ High switching capacity for direct control of appliances

industial controls

Summary of content (4 pages)

PAGE 1
Adaptation of the TCS-Cody 3 to special requirements: ® ® industial controls industial controls The TCS-Cody 3 is provided with a series of flexible time settings which allow the adaptation to special cases of application. For programming these special operating modes please ask for our flow chart for the TCS-Cody series, if required! Instructions for Assembly and Use TCS-Cody 3 Electronic encoder-type lock The TCS-Cody is a modern and safe alternative to traditional key switches.
PAGE 2
® industial controls Dear customer, ® industial controls Program 2 Clearing of a pass code The Cody which you have purchased is one of our highest quality technical products. We have taken the greatest care in its manufacture to ensure that this microprocessor controlled encoder reaches you in faultless condition. However in the unusual event of suspected equipment failure please return the appliance together with the enclosed warranty document to your dealer or direct to our factory.
PAGE 3
® ® industial controls industial controls Description of the appliance Program 2 Input / Clearing of a pass code Input 8-digit master code Push key button Sound signal 1 x short Input of 2-digit memory location e.g. 07 or 28 The TCS-Cody consists of a decoder and a keyboard. The units are connected by a simple double-wire cable without a special plug. Programming of the TCS-Cody is possible with the keyboard and the master code.
PAGE 4
® ® industial controls industial controls Assembly Instructions Assembly of the CODY keyboard: 1. By slightly pushing the two latches at the right and left side of the keyboard from behind to the edge, remove the small frame from the keyboard. 2. Now you see two fixingholes (diam. = 4 mm) at the front of the keyboard. By means of these you can fix the keyboard onto the wall. 3. Connect the keyboard to the logic unit by means of a twin-cable (up to 5 m long).