Installation guide

InstaJlation
O_udr.. (/##hb?£ Caterers
ELECTRICAIJ SUPPLY
Models _qth rotisserie require 1i2(iV, 60Hz.
and c{mnected to an h_divkhml properly
grom]ded brm_ch circlfit protected bv a ]i5
amp circuit breaker or time delay fl_se.
The power cord om]the rotisserie is e(pfipped
_qth a three-prong (grom]dh_g)plug _hich
mates _qth a standard three-prong grom]dh]g
Ball receptacle to mim]imize the possibility of
shock hazard f&m/ this applim_ce.
If the electHcal serv]ce provi ded does m]ot
meet the above specificathms, it is rec]}m-
mended that a ]icem]sed electrician h]staH an
approve(] omlet.
DO N ()T [ _NDER ANY C_IR(Z _MS3;4N (ES,
C2_T OR REMOVE THE THIRD (GROI _ND)
PRONG FROM THE POWER (ORD.
* For 27" _qde blfi]t-in grills, locate the
e] e ctri cal ol_t] e t o]] the ]eft ha]] d si d e _ i thin
reach of the roti sseri e' s 72" p(B_ er cord.
* For 36" and 48" _qde built-in grills, locate
the electrical om]et om_ the right hm]d side
_ ithh_ reach of the roti sser] e's 3(]" po_ er
co1"d.
e.%j%)"
Leaks
TEST FOR I _EAKS
A corn pl et e gas tigh m ess ch eck m I_st be
per{ormed at the installation site. Do clot
I_se a flame to check _i}r gas leaks.
* Do m]ot I]se the grill m'_ti] a]] con n ecti on s h ave
been leak tested.
*Repeat leak test after each l,P tank cham]ge.
* (2beck to be sm'e the main \;live {m the LP
tan k or the sh i_t-o{t vn]ve i s in th e "OFF'
+Make a soap so] mion of on e part ]iq ui d
detergent an]d oil e part P,ater+
The valve pm]e] midst be removed to check the
valves mid fittings.
*All control w]]ves sho_]]d be icI the "()FF"
* Remove the knobs.
* ()n models eq_fipped _ith Rotisserie, remove
the sa[ety wdve p_shbmto_ m_d m_scre_ the
* Rein ore the 4 scre_ s h oldi_ g the valve pan el
to the grill
* P_I]] the pan e] o_ltp, ards a]] d mlp] _lg th e _Aires
fi'om the back of the rotary igniters.
* If the grill h as m] opti onal roti sserie b_rn er,
remove the scre;%s ho]dh]g the i_]specthm
cover hi place.
TO TEST:
* Apply the s(}ap soh_tion arom]d the
co111]ecti {ms, \;live a_]d t_]b] Ctg.
* Tm'n the gas supply on.
* Check a]] com]ections t]'om the s_pp]y ]i_]e
or I,P tal]k _p to a_/(] inch_ding the manifo]d
pipe assemb]v_
* If a ]eak is detected, tm'_ gas s_pp]y to off
and tighten fittings. Tm'n the gas on mid
* To re-i_] stall th e valve pm] e], re-con n ect th e
igniter wires mid secrete the pane] with
original screws.
I 0