Installation I struct" n Automatic Icemaker ZDIC150 ZDIS1S0 Design Guide With Instollotion Instructions monogram.
Installation • BEFORE YOU BEGIN: Read these instructions completely CONTENTS and carefully. • IMPORTANT: Save these instructions for local inspector's use. • IMPORTANT: Observe all governing codes and ordinances. , Note to InstallerBe sure to leave these instructions with the Consumer. , Note to Consumer - Keep these instructions with your Owner's Manual for future reference. -&WARNING: This appliance must be properly grounded. Failure to do so can result in death, fire or electrical shock.
Design Information MODELS AVAILABLE ZDIC150, Available ZDIS150 in black and stainless The icemaker may be installed or used free-standing. steel, below a countertop CUTOUT & PRODUCT DIMENSIONS Flush Installation, custompanel will requirean additional 1-1/2"wide filler ./The ofside. a 3/4" thick stripinstallation on the hinge 34" to 34-1/2" 15 Top View 1/2"-wide filler X, panel or cleat set "15-1/2" *'16-1/2" backevenwith frontofcase.\ CABINET 34" rain.
Installation Instructions OPTIONAL ACCESSORIES ZIP75BB Black--For the installation of a trimless ZPK1--Drain Pump Kit. For use when a floor drain is not available. The drain pump must be installed inside the unit and can operate at a maximum vertical height of 10 feet. 10 feet of tubing is supplied with the kit. 3/4" thick custom panel on black models (not for stainless steel models). This kit provides a handle that can be installed with the custom panel.
Installation ADVANCE PLANNING CAUTION: Due to excessive weight, TWO PEOPLE ARE REQUIRED TO MOVE AND INSTALL THIS ICEMAKER. Failure to do so can result in back or other injurg. MISE EN GARDE : A cause de son poids_lev_,ILFAUT DEU× PERSONNES POUR DEPLACER ET INSTALLER CETTE MACHINE A GLA_ONS. Le non-respect de ces instructions peut causer des blessures Instructions ADVANCE PLANNING Before you begin: 1. If a custom panel is to be installed, follow the instructions shown on pages 10 and 11.
Installation Instructions POWER SUPPLY WARNING: (Please read carefu,y . FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. Failureto followthese instructions can resultindeath,fireor electrical shock. AVERTISSEMENT : (S'ilvous lisez avec soin). POUR VOTRE S#CURITI_, CET APPAREIL DOIT i:TRE CORRECTEMENT MIS #, LA TERRE. Le non-respect de ces instructions peut causer la mort, un incendie ou un choc _lectrique.
Installation Instructions WATER SUPPLY WATERSUPPLY (cont.) • A cold water supplg is required for icemaker REVERSE OSMOSIS WATER SUPPLY IMPORTANT: The performance of the icemaker may be affected when it is connected to a reverse osmosis system. operation. The water pressure must be between • The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the icemaker needs to be between 30 and 120 psi. 30 and 120 p.s.i.
Installation Instructions CONNECT WATER SUPPLY REVERSE THE DOOR SWING • The water line should be flushed to clear ang foreign material before connecting to the icemaker. IMPORTANT: Disconnect power to the icemaker. • Connect the water line to the water supplg tube outside of the rear access cover.
Installation Instructions REVERSE THE DOOR SWING {cont.} REVERSE THE DOOR SWING {cont.} Reverse the hinges (all models}: • Remove the screws opposite the door hinges, top and bottom. Set aside. Reinstall the door (all models} (cont.}: TopHinge / • Remove the two screws holding top hinge. • Turn the hinge upside down, with the hinge pin pointing up. Reinstall the hinge on the opposite side at the bottom of the door. • Remove the bottom hinge.
Installation Instructions • BEFORE YOU BEGIN: Read these instructions completely NOTE: If installing a 3/4" trimless custom panel, a 1-1/2" wide filler strip mag be required. The filler strip will act as a spacer between the icemaker case and the adjacent cabinet, and will prevent interference with the icemaker door swing when it is installed between frameless or framed cabinetrg. The width of the cutout opening must include the width of the filler strip.
Installation STEP 2 Instructions DISCONNECT POWER TO THE ICE MACHINE for ZIP75BB Kit STEP5 SECURE SIDE TRIM PIECES TO CUSTOM PANEL • Lay the custom panel appearance-side-down on a clean surface. STEP 2 REMOVE HANDLE AND NAMEPLATE • Align top and bottom panel sides. side trim to the custom • Remove the door handle bg removing the two top mounting screws. Set screws aside. Discard handle. Tape the side trim pieces to the back of the custom panel.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in _lour area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub.No. 31-46199-2 PartNo.
