GE Inspection Technologies Remote Visual Inspection 1.4 mm Working Tools Operating Manual www.geinspectiontechnologies.
1.4 mm Working Tools Table of Contents What You Have Received.......................................................................1 Distally Inserted Tools...........................................................................1 Proximally Inserted Tools......................................................................3 Safety Cap . .......................................................................................5 Tools Requiring Disassembly................................................
1.4 mm Working Tools Distally Inserted Tools (continued...) 1 2 Carefully slide tool through the working channel to the desired location. Find the proximal end of the working tool and carefully insert the tool into the working channel at the distal end of the VideoProbe®. www.geinspectiontechnologies.
1.4 mm Working Tools Proximally Inserted Tools Part Number: Description: WT-141432P WT-141426P WT-141432A WT-141426A WT-141432S WT-141426S 1.4mm Three Prong Gripper Tool 3.2M Working Length 1.4mm Three Prong Gripper Tool 2.6M Working Length 1.4mm Alligator Tool 3.2M Working Length 1.4mm Alligator Tool 2.6M Working Length 1.4mm Snare Tool 3.2M Working Length 1.4mm Snare Tool 2.
1.4 mm Working Tools Proximally Inserted Tools (continued...) 2 3 Use the clip on the Umbilical tube to keep Plunger Handle secure when not in use. Carefully slide tool through the working channel to the desired location. www.geinspectiontechnologies.
1.4 mm Working Tools Safety Cap 1 Use the supplied safety cap to secure the end of non-plunger activated tools. www.geinspectiontechnologies.
1.4 mm Working Tools Tools Requiring Disassembly Part Number: Description: WT-143032A WT-143026A 3.0mm Alligator Tool 3.2M Working Length 3.0mm Alligator Tool 2.6M Working Length Key: WT=Working Tool, First Two Digits=Cable Diameter, Third and Forth Digits=Tool Diameter, Fifth and Sixth Digits=Working Length. 1 Plunger handle of working tool must be dissembled prior to insertion into the working channel. a Loosen thumbscrew. www.geinspectiontechnologies.
1.4 mm Working Tools Tools Requiring Disassembly (continued...) b Slide back black Actuator. c Unscrew metal cap. www.geinspectiontechnologies.
1.4 mm Working Tools Tools Requiring Disassembly (continued...) d Remove cable pin from cable. d Remove metal cap from cable. 2 Insert proximal end of cable through the distal end of the VideoProbe®. 3 Re-assemble plunger handle in reverse order of Step 1 (e-a). NOTE: On re-assembly make sure enough of the cable is showing so thumbscrew makes a good connection. www.geinspectiontechnologies.
1.4 mm Working Tools Hook / Comparitor (Gage) Assembly Part Number: Description: WT-H WT-C Hook Piece (Qty 5) Comparitor Piece (Qty 5) Key: WT=Working Tool, First Two Digits=Cable Diameter, Third and Forth Digits=Tool Diameter, Fifth and Sixth Digits=Working Length. NOTES: • Always check the hook and comparitor (gage) assemblies prior to inspection of an engine for any looseness, bends, deformity, or other irregularities. • Check the threaded portion of the spring shaft.
10 1.4 mm Working Tools Hook / Comparitor (Gage) Assembly (continued...) 2 Screw the hook over the spring shaft’s distal end slowly turning the hook clockwise. www.geinspectiontechnologies.
1.4 mm Working Tools 11 Environmental Compliance The equipment that you bought has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment. In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems.
12 1.4 mm Working Tools Service Contact Information USA GE Inspection Technologies Product Service Dept. 721 Visions Drive Skaneateles, NY 13152 Germany GE Inspection Technologies Lotzenäcker 4 72379 Hechigen Hong Kong GE Inspection Technologies Unit 1602, 16/F Sing Pao Building 101 King's Road North Point, Hong Kong Tel: 315-554-2000 ext. 1 Fax: 866-899-4184 Email: rvi-service@ge.com Tel: +49-7471-9882 20 Fax: +49 7471-9882 30 Email: rvi-infoeuropa@ge.
Customer Support Centers North/South America 721 Visions Drive Skaneateles, NY 13152 Tel: 888-332-3848 315-554-2000 ext. 1 Email: geit-info@ge.com Europe Lotzenäcker 4 72379 Hechingen Germany Tel: +49 (0) 7471 9882 0 Email: rvi-infoeuropa@ge.com Asia/Pacific Unit 1602, 16/F Sing Pao Building 101 King’s Road North Point Hong Kong Tel: +852 2877 0801 Email: rvi-infohongkong@ge.com www.geinspectiontechnologies.com ©2008 General Electric Company.
